the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2009 toyota corolla add on starter


Post ReplyPost New Topic
< Prev Topic Next Topic >
miro2u 
Member - Posts: 7
Member spacespace
Joined: August 14, 2005
Location: Canada
Posted: July 29, 2009 at 7:07 PM / IP Logged  
Need help finding wire that gives negative or positive output when lock button is pressed on factory remote. Add-on(mars 10) is installed and working if i manually give 4 ground impulses, only thing left is finding wire to hook up. Wire that triggers door lock wont work because its dead when remote button is pressed.Any suggestion is appreciated.
Thank You.
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: July 29, 2009 at 8:00 PM / IP Logged  

If the car is running, does the keyless entry still operate the door locks?  If it does not, once you remote start the car, you will not be able to kill it with the remote.

Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
miro2u 
Member - Posts: 7
Member spacespace
Joined: August 14, 2005
Location: Canada
Posted: July 29, 2009 at 8:45 PM / IP Logged  
No remote does not work after car is running, I`m aware of that and its OK. Key will have to be used to enter vehicle and shut it down if needed.
i am an idiot 
Platinum - Posts: 13,693
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: July 29, 2009 at 9:13 PM / IP Logged  

What color wire and what location did you try to use?   Audiovox has the following info for your vehicle. 

2009 toyota corolla add on starter -- posted image.PowerLockPINK(-)DRIVERS KICK PANEL IN HARNESS FROM DRIVERS DOOR

Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
miro2u 
Member - Posts: 7
Member spacespace
Joined: August 14, 2005
Location: Canada
Posted: July 29, 2009 at 9:20 PM / IP Logged  
That is the one i was trying to use. If i use that one i can start vehicle pressing lock 4 times on the doors but not with remote.
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: July 29, 2009 at 9:48 PM / IP Logged  
You want to use the wire listed as "lock motor" on most tech sheets. This wire will shows +12v when locking with the remote or switch on the door. According to the link below it is BROWN or ORANGE depending on the model of Corolla you have. You can find the wire in the drivers kick panel. You may need to use a relay to switch the polarity if your unit requires a (-) signal.
https://www.the12volt.com/installbay/forum_posts.asp~TID~102124
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: July 30, 2009 at 10:09 AM / IP Logged  
Come to think of it you will need relay driven lock outputs from your unit, you have to open the lock wire. Also and I'm asking not telling, isn't there a key-sense wire one could use?
miro2u 
Member - Posts: 7
Member spacespace
Joined: August 14, 2005
Location: Canada
Posted: July 30, 2009 at 3:40 PM / IP Logged  
JWorm wrote:
You want to use the wire listed as "lock motor" on most tech sheets. This wire will shows +12v when locking with the remote or switch on the door. According to the link below it is BROWN or ORANGE depending on the model of Corolla you have. You can find the wire in the drivers kick panel. You may need to use a relay to switch the polarity if your unit requires a (-) signal.
https://www.the12volt.com/installbay/forum_posts.asp~TID~102124
I will try using "lock motor" wire trough relay to get negative.Let you know what happens. Thank you for suggestion.
miro2u 
Member - Posts: 7
Member spacespace
Joined: August 14, 2005
Location: Canada
Posted: July 30, 2009 at 3:48 PM / IP Logged  
howie ll wrote:
Come to think of it you will need relay driven lock outputs from your unit, you have to open the lock wire. Also and I'm asking not telling, isn't there a key-sense wire one could use?
There is(blue @ignition switch), but how would i use keysense wire to neg. impulse? Or maybe i did not understand what you mean.
Mike M2 
Platinum - Posts: 2,652
Platinum spacespace
Joined: June 29, 2005
Location: United States
Posted: July 31, 2009 at 6:32 AM / IP Logged  
Listen to what Jworm has posted, it's the correct way to do this. The wire is in the harness coming in from the drivers door...
Mike M2
Tech Manager
CS Dealer Services

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer