the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

avital 4113 and pkall


Post ReplyPost New Topic
< Prev Topic Next Topic >
aoza 
Member - Posts: 4
Member spacespace
Joined: December 22, 2010
Location: New York, United States
Posted: December 22, 2010 at 1:22 PM / IP Logged  
Happy Holidays Everyone,
Getting ready to install Avital 4113 with PKALL on a 2004 Lexus RX330 with a D2D cable. The PKALL install looks pretty straight forward, but not sure what needs to get wired for the Avital 4113 using D2D. Here is the wiring diagram for the 4113. Any help would be greatly appreciated.
H1/1: (-)Factory alarm disarm
H1/2: (-)Factory rearm
H1/3: (+)Ignition out (to alarm)
H1/4: (-)Activation Input
H1/5: (-)Ground when locked
H1/6: (-)Horn Output
H1/7: (-)Trunk Release Output
H1/8: Ground
H1/9: (+/-) Light Flash
4-pin satellite harness
1: (-)Status Output
2: (-) Accessory Output
3: (-) Starter Output
4: (-) Ignition Output
Heavy gauge relay wiring
1: (-) Output to Ignition Circuit
2: (-) Output to Starter Circuit
3: (-) Output to Accessory Circuit
4: (-) (30A) High Current 12 Input
5: (-) Programmable output for accessory or ignition
6: (-) (30A) High Current 12 Input
Door lock harness
1: (-) Unlock output
2: N/A
3: (-) Unlock output
Remote start harness (H2)
H2/1: (-) Neutral safety switch input
H2/2: Tachometer wire
H2/3: (+) Brake switch shutdown
H2/4: (-) Hood pin switch
H2/5 (-) 200ma 2nd status/rear defogger output
Twelvoltz 
Platinum - Posts: 2,384
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: March 24, 2005
Location: New Jersey, United States
Posted: December 27, 2010 at 7:16 AM / IP Logged  
Your vehicle's keyless entry does not work when the car is running. You will either have to run wires into the door to unlock while the vehicle is running or 5-wire the driver's door actuator. Since you are using a one button remote start, I would suggest using a 5-wire setup on the driver's door unlock motor leg in the kick panel, this would only unlock that door but would save the effort of going into the door.
That car has two starter wires, so you will need to add a relay activated by the small purple wire.
You will also have to use one of the status outputs to the keysense wire in the vehicle to disarm the factory alarm while remote starting.
Installer, IT support, and FFL. I need less hobbies.
aoza 
Member - Posts: 4
Member spacespace
Joined: December 22, 2010
Location: New York, United States
Posted: December 30, 2010 at 12:46 PM / IP Logged  
Thanks for your input... very helpful..

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer