CN1 Main Harness
1 Red (+) 12V Constant (+) +12 V, White Pin 1
2 GREEN / WHITE (+) Parking Light Output NOT USED
3 RED / White (+) 12V Constant (+) +12 V, White Pin 1
4 White (+) Accessory (+) Accessory 1, Orange Pin 2
5 Blue (+) Selectable by jumper*** (+) Accessory 2, Red pin 3
6 Yellow (+) 12V Starter (+) Starter, Yellow, pin 5
7 Green (+) 12V Ignition (+) Ignition, Blue, pin 2
8 Black (-) Ground Ground
***Change Jumper to Accessory***
CN2
1 GREEN / WHITE (-) Parking Light Output (-) Parking Lights: White Connector Gray, pin 8
2 RED / Black (-) Starter Output --wire to bypass (relay for +) Starter Output???
3 WHITE/ Black (-) 2nd Accessory Output not used???
4 Black (-) Status Output (POC #1) Ground
5 Orange (-) Rearm Output (POC #2) (-) Parking Lights: White Connector Gray, pin 8
6 ORANGE / White (-) Disarm Output (POC #3) --wire to Bypass (Brown) Disarm Input
7 White (-) Horn Output (POC#4) **where is the horn wire?
8 Gray/Black (-) Hood Pin Input --wire to Bypass Hood Status (-) Input
9 Light Blue/White (+) Foot Brake Input --wire to Bypass Brake Status (-) Input
10 RED / White (-) Trigger Start Input not used??
11 Red (+) Trigger Start Input not used???
12 Yellow/Black (+) Tach/Alt Sense Input --wire to Bypass TACH (AC) Input
CN3 – Lock Connector
1 None (+12V) Constant
2 Violet/White (-) Trunk Release --wire to Bypass Trunk (-) Output
3 ORANGE / Black (-) Driver’s Priority Unlock ??? Where do I connect this??
4 Blue (-) Unlock Output --wire to Bypass Unlock (-)
5 Blue/Black (-) Lock Output --wire to Bypass Lock (-)
6 None (-) Ground
CN4 – 4-Pin (RS232 Port)
Does this come with the remote start or the bypass? Or is this a separate purchase?
Idatalink ADS-ACLA Bypass ADS-AL(DL)-HA3-EN
D2D Cable – Does this come with the remote start of the bypass? Or is this a separate purchase?
IF D2D is available // is covered by D2D (1-way remote start)
Blue/White - GWR (-) Input //Ground (Auto Transmission)
Black – Ground //Ground
Red – 12V (+) //12V (+)
GREEN/ Black - Lock/Arm (-) Input //RS CN3 Blue/Black (-) Lock Output
Blue/Black – Unlock (-) Input //RS CN3 Blue (-) Unlock Output
RED / White – Trunk (-) Input //RS CN3 Violet/White (-) Trunk Release
Brown – Disarm (-) Input //RS CN2 ORANGE / White (-) Disarm Output (POC #3)
PURPLE / Black – Ground (-) Input Ground (to enable Auto Relock after Start)
BLACK/ White – Starter (+) Input //RS CN2 RED / Black Starter (-) >> Relay for (+)
Green – E-Brake Status (-) Output What do I connect this to?
PURPLE / White – Tach (AC) Output CN2 Yellow/Black Tach/Alt sense Input
WHITE/ Black Bypass – GREEN/ Red – Door Lock
WHITE/ Red – Unlock (-) (-)Unlock: 16 pin Blue Connector, Grey, Pin 18
White – Lock (-) (-)Lock: 16 pin Blue Connector, Blue, Pin 11
Yellow/Black – Door Status (-) Output Remote Start does not have this? – not connected?
Yellow/Red – Trunk Status (-) Output Remote Start does not have this? – not connected?
Yellow – Hood Status (-) Output Remote Start - Gray/Black (-) Hood Pin Input
BROWN / Red – CANH 7-pin immobilizer connector – Pink, Pin 4
BROWN / Yellow – CANL 7-pin immobilizer connector – Blue, Pin 3
ORANGE / Black – Key Data 7-pin immobilizer connector – Lt. Green, Pin 6
Pink – Ignition (+) Input 7-pin immobilizer connector – Color?, Pin 2
GREEN/ Red – Door Lock Bypass – WHITE/ Black
Gray/Red – Brake Status (+) Output CN2 Light Blue/White (+) Foot Brake Input
Is this all I need for W2W connections? Am I missing any connections? And is there any D2D cable that comes with either the bypass or remote start?
misturnice