Hello,
I have a Toyota Camry 2017 without Smart Start and Viper 5706V with Dball2 module
I am using D2D and this is my wiring:
VIPER
Main Harness, White 6-pin connector
01.RED (+)12VDC Constant Input @ Ignition Switch Harness,Pin 5,GREEN
02.BLACK (-) Chassis Ground @ Grounding Screw
03.BROWN (+) Siren Output @ Viper Siren
04.WHITE/ BROWN Parking Light Isolation @ Not used
05.WHITE Parking Light Output @ Not Sure
Door Lock, 3-Pin Connector
01.BLUE (-) Unlock Output @ Not Used
02.NC
03.GREEN (-) Lock Output @ Not Used
Remote Start Harness, 10-Pin
01.NC
02.RED / BLACK (+)12VDC @ Ignition Switch Harness,Pin 5,GREEN
03.PINK/BLACK Not Used
04.PINK/WHITE (+)Ignition 2 @ Ignition Switch Harness,Pin 1, PINK
05.RED (+)12VDC @ Ignition Switch Harness,Pin 5,GREEN
06.GREEN (+)Starter Input @ Ignition Switch Harness,Pin 7, BLUE (Key Side)
07.VIOLET (+)Starter Output @ Ignition Switch Harness,Pin 7, BLUE (Car Side)
08.ORANGE Accessory Output @ Not Used
09.RED / WHITE (+)12VDC @ Ignition Switch Harness,Pin 5,GREEN
10.PINK (+)Ignition 1 @ Ignition Switch Harness,Pin 6,BLACK
Auxiliary 24-Pin Connector
01 PINK/WHITE (-) 200mA Ignition 2/Flex Output @ Not Used
02 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT @ Not Used
03 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT @ Not Used
04 BLACK / YELLOW (-) 200mA DOME LIGHT OUTPUT @ Not Used
05 DARK BLUE (-) 200mA STATUS OUTPUT @ Not Used
06 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT @ Not Used
07 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT @ Not Used
08 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT @ Not Used
09 GRAY (-) HOOD PIN INPUT (NC OR NO) @ Not Used
10 BLUE (-) TRUNK PIN/INSTANT TRIGGER INPUT (N/C OR N/O) @ Not Used
11 WHITE/ BLUE ACTIVATION INPUT @ Not Used
12 VIOLET/WHITE TACHOMETER INPUT @ Not Used
13 BLACK/ WHITE (-) NEUTRAL SAFETY /PARKING BRAKE INPUT @ Chassis Ground
14 GREEN/ BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT @ Not Used
15 GREEN (-) DOOR INPUT @ Not Used
16 BROWN / BLACK (-) 200mA HORN HONK OUTPUT @ Not Used
17 PINK (-) 200mA IGNITION 1 OUTPUT @ Not Used
18 VIOLET (+) DOOR INPUT @ Not Used
19 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT @ Not Used
20 BROWN (+) BRAKE SHUTDOWN INPUT @ Not Used
21 VIOLET / YELLOW (-) 200mA STARTER OUTPUT @ Pin 85 of Ext Relay
22 GRAY/BLACK (-) DIESEL WAIT TO START INPUT @ Not Used
23 ORANGE (-) 200mA ACCESSORY OUTPUT @ Not Used
24 GREEN / WHITE (-) 200mA FACTORY ALARM ARM OUTPUT @ Not Used
External Relay
Pin 85 @ Viper Pin 21.VIOLET / YELLOW
Pin 86 and 87 @ Ignition Switch Harness, Pin 4, Yellow (through 7.5A Fuse)
Pin 30 @ Ignition Switch Harness, Pin 3, LT GREEN
Pin 87a @ Not Used
General Purpose Diode across 85 and 86 with band toward 86
Xpresskit DBALL2
I follow xpresskit install diagram using D2D and connect only these wires:
14-Pin Harness, BLUE
3.TAN/BLACK
4.TAN
10.ORANGE / RED
11.YELLOW/RED
12-Pin Harness, RED
10.YELLOW/BLACK
11.ORANGE / BLACK
10-Pin Harness, BLACK
Not Used
4-Pin, WHITE
D2D to Viper
Remote start function works fine
Here are the problems:
1/ Somehow, Viper remotes only arm/disarm but don't lock/unlock.
OEM remotes lock/unlock just fine.
But if I remote start and while the engine is running, I can use Viper remotes to lock/unlock the doors.
2/ When I remote start, Viper locks all doors automatically. Is that normal behavior?
3/ No light flashes when arming/disarming. Should I connect wire 05.Parking Light Output?
Any idea would be great.
Thanks