Remote Start on a 2001 Montana

Home / the12volt's Install Bay / Car Security and Convenience / Remote Start on a 2001 Montana (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Vikerex

Member - Posts: 15

Joined: August 30, 2003

Location: United States

Posted: November 12, 2003 at 3:36 PM / IP Logged

Looking for a wiring diagram for a 2001 Pontiac Montana, I am installing a remote starter.

Thank you,

Ted

Just gettin' Started :>)

Vikerex

Member - Posts: 15

Joined: August 30, 2003

Location: United States

Posted: November 12, 2003 at 10:16 PM / IP Logged

Wiring diagram to install a remote starter

Just gettin' Started :>)

defective

Silver - Posts: 642

Joined: August 20, 2003

Location: Canada

Posted: November 13, 2003 at 8:58 AM / IP Logged

Same as a venture.

Here ya go:

12v+ - red - Ignition harness

Ignition - Pink - Ignition Harness

Second Ignition - White - ignition harness

Accessory - orange - Ignition harness

Starter - yellow - Ignition Harness

Parking Lights - brown(+) - drivers Kick panel

Lock - RED / black(-) - drivers kick panel

Unlock - ORANGE / black(-) - drivers kick panel

Arm/disarm - works with lock and unlock, dont worry about it

Trunk release - Blue(+) - passenger kick panel

OEM Horn - black(-) - steering column harness

headlights - yellow(+) - headlight switch

brakes - white(+) - at pedal

_________________________________________

will be an immobilizer system likely. So you will probably need an extra key to disarm the ignition.

Alpine Guy

Platinum - Posts: 2,478

This member has made a donation to the12volt.com. Click here for more info.

Joined: October 18, 2003

Location: Canada

Posted: November 13, 2003 at 8:04 PM / IP Logged

i did one today,,,i'll see if i can remember it off my head.

It had pkg3 transponder. I used a automobility PKG5 bypass, that is what was recommended.

12v- red and RED / white -ignition harness

ignition 1- pink -ignition harness

ignition2- cant remember

starter- yellow -ignition harness

accessories- orange -ignition harness

brake wire- white - at brake switch

parking light-brown -at blue plug right beside parking brake

tac wire- white -in harness that crosses the top of the engine on the passenger side ( in 1 inch split loom )

lock- blue - drivers door boot

unlock -white- driver door boot

disarm- ORANGE / black- driver door boot

* be shure to put in a relay for the 2nd ignition if you have a starter moduel with 1 ignition output.

hummmmm, my memory is pretty good after a 12 hour shift, lol

Alpine Guy

Platinum - Posts: 2,478

Joined: October 18, 2003

Location: Canada

Posted: November 13, 2003 at 8:05 PM / IP Logged

and the door locks are (-)

Vikerex

Member - Posts: 15

Joined: August 30, 2003

Location: United States

Posted: November 14, 2003 at 10:13 AM / IP Logged

If there is no factory car alarm installed, do I still have to use a bypass?

Just gettin' Started :>)

Alpine Guy

Platinum - Posts: 2,478

Joined: October 18, 2003

Location: Canada

Posted: November 14, 2003 at 8:57 PM / IP Logged

ya, that bypass is to make the vehicle think the starter is a coded key...if not it will shut off

Vikerex

Member - Posts: 15

Joined: August 30, 2003

Location: United States

Posted: November 15, 2003 at 1:12 AM / IP Logged

Immobilizer system? Extra key to disarm the system?

Not sure what you are talking about. There is no alarm system installed, the only thing that I can tell is this has is keyless entry. No special keys.

Just gettin' Started :>)

defective

Silver - Posts: 642

Joined: August 20, 2003

Location: Canada

Posted: November 15, 2003 at 7:55 AM / IP Logged

the black handle on the key will be large if it's an immobilizer, also security and ignition security are two different things, even the base models will have some type of ignition lock system. just look at the key, if it has a little square with steel contacts on each side it is a passlock, if it has a large base, it is immobilizer

Vikerex

Member - Posts: 15

Joined: August 30, 2003

Location: United States

Posted: November 15, 2003 at 8:14 AM / IP Logged

I looked at the key, under the black rubber there is an electrical contact? Now my question is how do I hook up the remote starter to by pass this? The starter is a DesighTech Basic remote starter Model: 20023.

Thanks

Just gettin' Started :>)

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.