the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

request for Celica 94 Alarm Wiring please


Post ReplyPost New Topic
< Prev Topic Next Topic >
legend9 
Member - Posts: 32
Member spacespace
Joined: March 11, 2003
Location: United States
Posted: December 26, 2003 at 9:02 PM / IP Logged  
Hi, Does anyone have the diagram for the celica 94 ? Please show me if you have it. Thanks.
Made in Japan
Teken 
Gold - Posts: 1,492
Gold spacespace
Joined: August 04, 2002
Location: Aruba
Posted: December 26, 2003 at 9:07 PM / IP Logged  
Start:   BLACK/ WHITE IGNITION SWITCH HARNESS
Ignition #1: BLACK/ ORANGE IGNITION SWITCH HARNESS
Ignition #2:   BLUE/RED IGNITION SWITCH HARNESS
Accessory:   GRAY IGNITION SWITCH HARNESS
Brake Light:   GREEN / WHITE (+) AT SWITCH ABOVE BRAKE PEDAL
Tach Signal:   GRAY AT IGNITER OR CHECK CONNECTOR *
Parking Lights:   GREEN (+) AT FUSE/JUNCTION BLOCK ('TAIL'FUSE)
Headlights:   RED / GREEN (-) AT HEADLIGHT SWITCH
Notes:
   * Igniter And Check Connector Located In Driver Rear Corner Of Engine Compartment.
--------------------------------------------------------------------------------
Toyota
Celica
1994-1995
Alarm and Keyless Entry Wiring Colors and Notes
Function
   Vehicle Color
Location
Constant +12 Volts:
   WHITE AND BLACK/ RED
IGNITION SWITCH HARNESS
Starter Kill:
   BLACK/ WHITE
IGNITION SWITCH HARNESS
Ignition +12 Volts:
   BLACK/ ORANGE
IGNITION SWITCH HARNESS
Dome Lights/Superv:
   RED / WHITE
(-) AT FUSE/JUNCTION BLOCK
OEM Horn:
   GREEN
(-) STEERING COLUMN HARNESS
Power Lock:
   BLUE/BLACK
DRIVER'S KICK PANEL **
Power Unlock:
   BLUE
DRIVER'S KICK PANEL **
Trunk Release:
   N/A
Alarm Input Wire:
   RED / WHITE
(-) AT FUSE/JUNCTION BLOCK
Notes:
** Child Safety Locks: GREEN (-) In Same Conn. As Door Lock Wires Above. See Note # 209 - Child Safety Door Lock Diagram.
legend9 
Member - Posts: 32
Member spacespace
Joined: March 11, 2003
Location: United States
Posted: December 27, 2003 at 10:48 AM / IP Logged  
Thanks a lot. =)
Made in Japan
Teken 
Gold - Posts: 1,492
Gold spacespace
Joined: August 04, 2002
Location: Aruba
Posted: December 27, 2003 at 11:21 AM / IP Logged  
Please varify *ALL* provided wiring codes with your DMM, and in the appropiate running modes of operation.
ie. Ignition location & varification = Will show +12 volts in the on / run position, AND crank / start.
You will varify this wire at least (2) times, with turning the key to the off position.
Please take your time, and be like a wood cutter, measure twice, cut once.
Regards
EVIL Teken . . .

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, May 24, 2025 • Copyright © 1999-2025 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer