Using door poppers with alarm

Home / the12volt's Install Bay / Car Security and Convenience / Using door poppers with alarm (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

lanman31337

Copper - Posts: 83

Joined: August 11, 2005

Posted: September 09, 2005 at 2:14 PM / IP Logged

Hello,

I'm just finishing up shaving my locks and handles, and I installed door solenoids and poppers in my car. In my alarm schematics it shows how to install the alarm with door lock/unlock soleniods, so I was just going to use the same wiring. My question is, it says the wires on the alarm are a negative trigger, so would I hook up the ground to the negative trigger, and the positive to a constant power source for my car?

lanman31337

Copper - Posts: 83

Joined: August 11, 2005

Posted: September 09, 2005 at 10:07 PM / IP Logged

Yeah, my schematics came with a setup with relays. Could someone answer the question for me please?

lanman31337

Copper - Posts: 83

Joined: August 11, 2005

Posted: September 10, 2005 at 7:32 PM / IP Logged

NM, i figured it out. I adapted the door lock wiring to just have the unlock to the solenoids.

Mr.Swifty

Member - Posts: 37

Joined: May 27, 2003

Location: Canada

Posted: September 15, 2005 at 3:37 AM / IP Logged

lanman31337 wrote:

NM, i figured it out. I adapted the door lock wiring to just have the unlock to the solenoids.

so does this mean every time you disarm the car both doors pop open???? It may be nice to have the drivers door on the pop with disarm and the passgener door pop with say and aux output. or disarm and one door per aux out?

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: September 15, 2005 at 9:20 AM / IP Logged

I use AUX channel 1 for driver's side and AUX channel 2 for the passengerside on the last car that had shaved door handles. The only bad thing about that is that you still have to arm and disarm before and after you open/close the doors.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

gcorrea

Silver - Posts: 436

Joined: May 22, 2004

Location: United States

Posted: September 15, 2005 at 5:07 PM / IP Logged

everyone that installs door poppers (that ive read about) asks the same question. would it be possible to add the selonoids in a drivers door priority configuration using only the lock unlock buttons of the alarm and not use up the other aux channels.on my alarm(k9 classic) it shows how to do the drivers door priority set up, unlock the door hit the unlock again within 5 seconds and unlock the pass. door. is there a wiring diagram on doing this with the selonoids?

gcorrea

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Using door poppers with alarm

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.