1999 Integra power door lock problem. Need Help!

Home / the12volt's Install Bay / Car Security and Convenience / 1999 Integra power door lock problem. Need Help! (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

DuTruo

Member - Posts: 10

Joined: November 24, 2002

Location: United States

Posted: December 04, 2002 at 10:54 PM / IP Logged

I just got a clifford IntelliVoice IQ installed and now the passenger door lock factory switch does not work, but it will lock when i armed the alarm. I tried taking the driver factory door lock switch and testing it on the passenger door and found out it's not the switch. On the driver side I found out that the middle wire going to the switch is +12 volt and when i tested the passenger side there was no reading on my volt meter, can someone help me? what was wired incorrectly when the alarm was installed?

Du Truong

10nesne1

Silver - Posts: 284

Joined: June 19, 2002

Location: British Columbia, Canada

Posted: December 05, 2002 at 12:37 AM / IP Logged

Acura

Integra

1996-2001

Remote Starter Wiring Colors and Notes
Function		Vehicle Color	Location
Start:		BLACK/ WHITE	IGNITION SWITCH HARNESS
Ignition #1:		BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition #2:		YELLOW	IGNITION SWITCH HARNESS
Ignition #3:		N/A
Accessory:		WHITE/ BLACK	IGNITION SWITCH HARNESS
Brake Light:		GREEN / WHITE (+)	AT SWITCH ABOVE BRAKE PEDAL
Tach Signal:		BLUE	AT DISTRIBUTOR OR TACH TEST CONN. *
Parking Lights:		RED / GREEN (+)	AT HEADLIGHT SWITCH **
Headlights:		RED / WHITE (+)	AT HEADLIGHT SWITCH
OEM Alarm Disarm:		BLUE (-)	AT SECURITY CONTROL MODULE ****
OEM Alarm Arm:		N/A
Diesel Glow Plug:		N/A	N/A
Clutch Bypass Wire:		BLUE/BLACK (-)	AT SWITCH ABOVE CLUTCH PEDAL
Notes:	* Distributor Located On Passenger Side Of Engine. Tach Test Connector Is a 2 Pin GRAY Connector Located On Driver Rear Of Engine On Strut Tower. Tach Wire Also Located In 16 Pin GRAY Connector Above Fuse Block Behind Driver Dash.

Acura

Integra

1996-2001

Alarm and Keyless Entry Wiring Colors and Notes
Function		Vehicle Color	Location
Constant +12 Volts:		WHITE/ BLACK	IGNITION SWITCH HARNESS
Starter Kill:		BLACK/ WHITE	IGNITION SWITCH HARNESS
Ignition +12 Volts:		BLACK / YELLOW	IGNITION SWITCH HARNESS
Dome Lights/Superv:		L GREEN/ RED (-)	14 PIN GRAY CONN. IN DR. KICK PANEL
OEM Horn:		BLUE/GREEN (-)	STEERING COLUMN HARNESS
Power Lock:		BLACK/ WHITE	14 PIN GRAY CONNECTOR IN DRIVER'S KICK
Power Unlock:		BLACK/ RED	PANEL***
Trunk Release:		N/A	CABLE OPERATED
Alarm Input Wire:		L GREEN/ RED (-)	14 PIN GRAY CONN. IN DR. KICK PANEL
Notes:	RED / BLACK (+) In 18 Pin BROWN Connector In Driver Kick Panel Can Also Be Used For Parking Lights. * See Note #201- Negative Pulse Door Lock Diagram. **** Security Control Module Located on Driver's Side Of Vehicle Right Of Steering Column.

DuTruo

Member - Posts: 10

Joined: November 24, 2002

Location: United States

Posted: December 05, 2002 at 10:38 AM / IP Logged

What is alarm input wire? is that where i'm suppose to connect the negative unlock wire from the alarm to, to fix my problem, thanks for all the help i will check out all the wiring again,

Du Truong

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1999 Integra power door lock problem. Need Help!

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.