Clifford RSX 3.5 R/S Issues

Home / the12volt's Install Bay / Car Security and Convenience / Clifford RSX 3.5 R/S Issues (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

alienhemi

Member - Posts: 2

Joined: October 21, 2006

Location: United States

Posted: October 21, 2006 at 7:20 PM / IP Logged

Good evening 12V experts, I come this forum hopefully for some resolution!

I have used the search function extensively with negative results.

I have a 2006 Dodge Ram 1500 Hemi (FIRST MISTAKE IN ALARM INSTALL 101) and installed the Clifford RSX 3.5 the other day.

Included in this install is the 530T / 508D / 556

Everything works except for this little nagging problem, when I remote start the truck and then get in and turn key on and disengage the alarm I get idiot lights like crazy!! Including the "ABS" and "BRAKE" light. Now start the truck with regular key no problems at all..

I did see something about a Diesel Install that mentioned idiot lights; however I did not know if that applied to this application..

Any help would be great.. Look forward to learning a lot from you folks..

Alien..

cntrylvr79

Silver - Posts: 582

Joined: July 02, 2005

Location: United States

Posted: October 21, 2006 at 11:43 PM / IP Logged

Sounds like you might not have all of the ignition wires powered up, or they're not being powered at the right time.

12volts	lt. blue/red (2A)	+	ignition harness
Starter	dk. GREEN/ YELLOW	+	ign harn or starter button (SRT-10)
Second Starter	PURPLE / brown	-	ignition harness
Notes: The second starter wire is negative trigger thru an 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.
Ignition	pink/white	+	ignition harness
Second Ignition	N/A
Third Ignition	N/A
Accessory	same as second starter wire	-	ignition harness
Notes: The accessory wire is negative trigger thru a 610 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.
Second Accessory	N/A

You're second starter and second accessory wires how did you tie into them? Like it says in the document in the link below?

http://www.directechs.com/techtips/pdfs/resources/security/directed_techtips/1084.pdf

If not I would start with those as the problem with your idiot lights

Cause I'm So white and nerdy...

First Class Certi-fried installer

alienhemi

Member - Posts: 2

Joined: October 21, 2006

Location: United States

Posted: October 21, 2006 at 11:47 PM / IP Logged

Yes the installer followed the TECHTIP1084 document, I was sitting in the passenger seat like an annoying customer would.. LOL

But yeah I watched him hook up two relays and all, he is going to call DEI on monday; however I was hoping to get some good answers here first..

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Clifford RSX 3.5 R/S Issues

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.