2004 Chrysler Intrepid Alarm/Remote Start Wiring

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / 2004 Chrysler Intrepid Alarm/Remote Start Wiring (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

malucyk

Copper - Posts: 56

Joined: October 13, 2002

Location: Canada

Posted: November 09, 2004 at 8:43 PM / IP Logged

Can someone post a wiring diagram for a 2004 Chrysler Intrepid.

Thanks

MAtt

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: November 10, 2004 at 8:36 AM / IP Logged

This is for Dodge Intrepid

I use OMEGA ByPASS # DB-CHDL-2PK for Transponder and Door Locks

Constant 12 volts	RED & PINK/BLACK	IGNITION SWITCH HARNESS
Ignition 12 volts	D BLUE/WHITE	IGNITION SWITCH HARNESS
Starter	YELLOW	IGNITION SWITCH HARNESS
Dome Light	YELLOW (-)	AT EITHER KICK PANEL OR BCM *
Trunk Pin Switch	TAN/BLACK (-)	22 PIN CONNECTOR HIGH IN DRIVER KICK
Parking Lamp	BLACK / YELLOW (+)	AT BODY CONTROL MODULE *
Power Lock	WHITE/ D GREEN	16 PIN CONN. IN ACCESS HOLE **
Power Unlock	SINGLE WIRE SYSTEM	IN DRIVER KICK OR HIGH IN DR.KICK

* Body Control Module (BCM) Located Behind Fuse Box. **Door Locks Require +12v Pulse Thru 2.7K Ohm Resistor For Lock And +12V Pulse Thru 620 Ohm Resistor For Unlock.

Single Wire Resistor Door Lock System

Accessories
Window Up	D\ WHITE P\ VIO/WHT D\ RED / BLK P\ GRN/WHT @ MAIN SWITCH
Window Down	F/ L BLUE F/ BRN/WHT R/ BLU/WHT R/ GRY/BLK
Ign Key Warn	LT BLUE (-)	IGNITION SWITCH HARNESS OR BCM *
Trunk Release	BLACK/ WHITE (+)	AT SWITCH OR BODY CONTROL MODULE **
OEM Horn	BLACK/ RED (-)	STEERING COLUMN HARNESS
Headlights	VIOLET OR VIO/RED (+)	AT BODY CONTROL MODULE **
OEM Alarm Arm	SINGLE WIRE SYSTEM
OEM Alarm Disarm	L GREEN/ ORANGE	DRIVER KICK PANEL OR BCM *

* Wire Found In BLACK 24 Pin Connector At BCM ** Body Control Module (BCM) Located Behind Center Of Dash. *** LT GREEN/ ORANGE Wire Must See A 12V (+) Pulse Thru A 587-681 Ohm Resistor To Disarm OEM Alarm (From Install). Wire Found In BLUE 16 Pin Connector.

Reversal Rest At Ground Power Window Circuit

Remote Start
Tach Signal	SEE NOTE *	AT POWERTRAIN CONTROL MODULE **
Ignition #2	D GREEN/ RED	IGNITION SWITCH HARNESS
Ignition #3	BLACK/ ORANGE	IGNITION SWITCH HARNESS
Accessory	BLACK/ WHITE	IGNITION SWITCH HARNESS
Neutral Safety	BLK/WHT OR BRN/YEL (-)	AT SWITCH ON TRANSMISSION OR PCM **
Brake Light	WHITE/ TAN (+)	AT SWITCH ABOVE BRAKE PEDEL
Reverse Light	VIOLET/BLACK (+)	AT SWITCH ON TRANSMISSION
Rear Window Defrost	DK BLUE/WHITE (-)	BCM 16 PIN BLUE CONN PIN #14

* Independent Coil System, TAN/PINK, TAN/L GREEN, TAN/L BLUE, TAN/RED, TAN/ORANGE, & TAN/D GREEN. Each Wire Is A Single Cylinder Signal. ** Powertrain Control Module (PCM) Located On Driver Side Front Fender Near Power Distribution Block.

Immobilizer Bypass

Don't Learn from Others Mistakes

You Might Be the One That Knows.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2004 Chrysler Intrepid Alarm/Remote Start Wiring

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.