the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

amp setting for component speakers


Post ReplyPost New Topic
< Prev Topic Next Topic >
stlyidklr 
Member - Posts: 11
Member spacespace
Joined: January 15, 2006
Posted: September 21, 2009 at 11:27 AM / IP Logged  
Right now I have a cheap power acoustic amp running some MB Quartz component speakers.  That amp is getting ready to die...shocker!  For my next higher quality amp, do I set the filter at high or full for the components?  I have MB Quartz in both the front and the back of my truck.  My amp for the rear speakers has already died.  So, I'm either going to go with a 4-channel or 2 2-channel.  Any suggestions there?  Thanks!
haemphyst 
Platinum - Posts: 5,054
Platinum spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: January 19, 2003
Location: Michigan, Bouvet Island
Posted: September 21, 2009 at 11:37 AM / IP Logged  
I've never heard of MB Quartz speaker systems, so I can't really tell you what that manufacturer's recommendations are.
Generally speaking, set the amplifier's high-pass to 80Hz or higher, to start. If you find you can't get adequate output with that frequency without the woofers "banging against the stops", raise the frequency. Personally, I'd never go much higher than about 100Hz, but that's just me. Others here might suggest differently.
A single 4-channel amplifier will have a smaller footprint than two 2-channel amps, and be easier to install - 1 power, remote and ground wire - and neater looking, IMO, as well. There is no "right" or "wrong" way, however.
It all reminds me of something that Molière once said to Guy de Maupassant at a café in Vienna: "That's nice. You should write it down."
stlyidklr 
Member - Posts: 11
Member spacespace
Joined: January 15, 2006
Posted: September 21, 2009 at 11:58 AM / IP Logged  
Thanks for the quick reply and info.  I made a miss type for the speakers.  They are MB Quart, no "z".  And the models are DSD-216 6.5" in the front and DUA-210 4" in the back.  I have them installed in a 2001 Nissan Fronteir Crew Cab. 
ianarian 
Copper - Posts: 516
Copper spacespace
Joined: April 24, 2009
Location: California, United States
Posted: September 21, 2009 at 8:09 PM / IP Logged  
Im with haemphy on the 100hz, sometimes even higher. I've noticed that higher quality amps get away with a lower Hz level. Perhaps due to clearer sound. Without subs, I would set my system to flat or the minimum HPF level.
This is what I do for FUN!
stlyidklr 
Member - Posts: 11
Member spacespace
Joined: January 15, 2006
Posted: September 22, 2009 at 12:35 PM / IP Logged  
I've squeezed in an Audiobahn 1051T subwoofer in the back run by a Kenwood KAC-7204 also.  I don't know if I have enough room to have a 4 channel under my seats.  I've already had to do some modifications to get the 2 2-channels to fit. Thank you both for the info!

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer