Solobaric S10D Wiring

Home / the12volt's Install Bay / Car Audio / Solobaric S10D Wiring (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

kenosha

Member - Posts: 7

Joined: June 05, 2003

Location: United States

Posted: June 12, 2003 at 7:24 AM / IP Logged

Could someone please confirm that I have selected the correct wiring method for my single Kicker Solobaric S10D. I'm looking for a 2ohm load, but the speaker specs are a bit misleading/confussing. They never actually state the impedance of a single voice coil. I think I may be making this harder than it should be.

Complete list of skeaker specs: http://www.kicker.com/images/manuals/SolodMan.pdf

Model: Kicker Solobaric S10D (old round ones)

Impedance (ohms): 2,4,8 <-------------------------------------------- hmmmmmm?

Max Amp Power: 450

Sensitivity: 87.6

Freq Response: 24-10

Rec Enclosure V: .66

Wired using following method:

Solobaric S10D Wiring -- posted image.

Will this give me a 2 ohm load, with this speaker?

kenosha

Member - Posts: 7

Joined: June 05, 2003

Location: United States

Posted: June 12, 2003 at 10:28 AM / IP Logged

I don't know why the pic didn't come through, here is the link:

http://www.rockfordfosgate.com/rftech/wiringwizard/index.asp?WoofQty=1+woofer&WoofImp=Dual+Voice+Coil+-+4+ohms+x+2&image.x=21&image.y=12

bberman1

Gold - Posts: 2,314

Joined: March 11, 2002

Location: United States

Posted: June 12, 2003 at 10:39 AM / IP Logged

What is the exact model # on the back of your sub? Also do you have a voltage meter?

kenosha

Member - Posts: 7

Joined: June 05, 2003

Location: United States

Posted: June 12, 2003 at 12:50 PM / IP Logged

Unfortunately I don't have the subs here at my new residence yet, they are back in Wisconsin. They are the S10D if that helps.

Yes, I have a $14 radio shack DMM

bberman1

Gold - Posts: 2,314

Joined: March 11, 2002

Location: United States

Posted: June 12, 2003 at 2:28 PM / IP Logged

Well without the model number I can’t tell you if it’s a 2, 4, or8 ohm model. And if I don’t know how many ohms they are then I couldn’t tell you how to wire them. But when you get them if you can’t figure out the ohms you can use a voltage meter to measure how many ohms they are. You can read how to measure the ohms here http://www.eatel.net/~amptech/elecdisc/ . But when you get them give me the model # and I will tell you how many ohms they are and how to wire them.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Solobaric S10D Wiring

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.