the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

autopage rf 420lcd, 04 mazda 3


Post ReplyPost New Topic
< Prev Topic Next Topic >
swatsquadgr 
Member - Posts: 6
Member spacespace
Joined: January 04, 2008
Location: Greece
Posted: January 11, 2008 at 9:02 AM / IP Logged  
According to my vehicle wiring diagram I have one cable per door (sum 4 cables) and a negative (-) trigger . My alarm is autopage RF-420. Which graph applies to me (5 Wire Alternating , reverse polarity ...) ? Do I need to use relays and diodes ? If you can tell me what cable connects where I would appreciate it .
My alarm also has a 200mA (-) timer output . Can I use it to close all windows or do I need relays ?
Thank you all for your help to a newbie .
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: January 12, 2008 at 10:53 PM / IP Logged  

For locks you should not need relays Lock is (NEG)- thru a 1Kohm resistor, and unlock is ground thru NO resistor.

Follow this diagram, pretend it doesn't say Caravan. Just for ref. the resistor values are of course different.

swatsquadgr 
Member - Posts: 6
Member spacespace
Joined: January 04, 2008
Location: Greece
Posted: January 15, 2008 at 9:13 AM / IP Logged  
1) My vehicle (mazda 3) wiring diagram mentions parking light (-) and (+).The first is at the harness and the 2nd at the headlight switch. Can I use only the (-) that my alarm supports ? Should I use relays ? The alarm output mentions it as "parking relay output +12 V 10A".
2) CAn I use the same output for both trunk light and hood pin ? Can I use another (-) output to connect to the trunk light wire ?
Thanks
chadwa2003 
Copper - Posts: 353
Copper spacespace
Joined: January 08, 2005
Location: Canada
Posted: January 15, 2008 at 5:40 PM / IP Logged  
Your mazda 3 should have a neg trigger at the headlight switch for parking lights I beleive it is a BLACK/ white wire. Yes you should use a relay if your unit doesn't support negative parking lights. Also you can use the same input for your negative trigger for trunk and hood just make sure to diode isolate to prevent any feedback. Best of luck with your install.
swatsquadgr 
Member - Posts: 6
Member spacespace
Joined: January 04, 2008
Location: Greece
Posted: January 16, 2008 at 7:49 AM / IP Logged  
thank you chadwa2003 for your help
hydroz_23 
Copper - Posts: 97
Copper spacespace
Joined: November 20, 2006
Location: United States
Posted: January 24, 2008 at 10:37 PM / IP Logged  
just use the factory arm and disarm wires, no resistors
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: January 25, 2008 at 9:09 AM / IP Logged  
The disarm on this car requires a nearly 3 second pulse....
hydroz_23 
Copper - Posts: 97
Copper spacespace
Joined: November 20, 2006
Location: United States
Posted: January 25, 2008 at 6:38 PM / IP Logged  
KarTuneMan wrote:
The disarm on this car requires a nearly 3 second pulse....
i have never had that issuse. it will unlock instant. did one today
chadwa2003 
Copper - Posts: 353
Copper spacespace
Joined: January 08, 2005
Location: Canada
Posted: January 25, 2008 at 6:48 PM / IP Logged  
It will not need an extended pulse it just will unlock the driver door and then unlock all the others right after. BLACK/ white and BLACK/ blue in the kick panel. There are only one of each test using the key cylinder straight ground and alot easier. You will have to unlock before and lock after start or hook up the key sense wire.
swatsquadgr 
Member - Posts: 6
Member spacespace
Joined: January 04, 2008
Location: Greece
Posted: March 01, 2008 at 8:05 AM / IP Logged  
My alarm ( autopage rf-420) has a 4 wire port for an optional sensor and I have a 3 wire radar sensor . Is to possible to hook it up ?
Radar wires -> blue -red - black
alarm optional sensor port wires -> blue - red - black - green
I have already tried by not connecting the green wire but the radar doesn't work.
Thanks for your help
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer