2005 mustang, remote start

Home / the12volt's Install Bay / Car Security and Convenience / 2005 mustang, remote start (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Teamrf

Gold - Posts: 1,031

Joined: January 13, 2004

Location: United States

Posted: April 27, 2009 at 2:03 PM / IP Logged

When I try to R/S the vehicle, the "theft/key" light flashes and the radio powers on but the starter doesn't even try to start. When I put the key in the "on" position, the car will start and die after a few seconds. On the alarm I am using the Tachless mode, but maybe I should find the tach wire. My guess is that the remote start is missing something which is not allowing me to program the PKALL. I thought everything was all ready to go.

I also need the factory disarm wire and the door trigger wires. Any idea on those?

~The Rookie~

Rookie of the year that is...

Don't let the smoke out of your equiptment..it doesn't go back in.

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: April 27, 2009 at 9:11 PM / IP Logged

What is your RX and TX wires ?

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

Teamrf

Gold - Posts: 1,031

Joined: January 13, 2004

Location: United States

Posted: April 29, 2009 at 9:24 AM / IP Logged

I want to say they are at pin 3 and 4 of the car I'm not really sure. But I think it is hooked up correctly because the dash theft light goes out when I go through the programming steps.

~The Rookie~

Rookie of the year that is...

Don't let the smoke out of your equiptment..it doesn't go back in.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: April 29, 2009 at 9:29 AM / IP Logged

Find the tach signal ( injector wire ) and program the tach. Test the remote starter after this and if you still have this program, try the key in the ignition but this time make sure that you disconnect the PKALL module. Post your findings.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Teamrf

Gold - Posts: 1,031

Joined: January 13, 2004

Location: United States

Posted: April 29, 2009 at 10:52 AM / IP Logged

Ok will do. I wont have the car again until the weekend. I was going to rip out EVERYTHING and start fresh. Can I find the OEM disarm and the door trigger wires on the driver side or do I have to go to the passager side?

~The Rookie~

Rookie of the year that is...

Don't let the smoke out of your equiptment..it doesn't go back in.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2005 mustang, remote start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.