the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

astro flex serie 120 remotes programming


Post ReplyPost New Topic
< Prev Topic Next Topic >
char_hanson 
Member - Posts: 2
Member spacespace
Joined: May 07, 2009
Posted: May 10, 2009 at 5:36 PM / IP Logged  

I have an AstroFlex Serie 120 in a 1995 Jeep Cherokee.  It was working great, but blew a fuse and now I can't get the remotes to work.

I have found the installation and programming instructions, but they don't say anything about programming the remote.

Is there anyone who can help me?

Thanks

KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 10, 2009 at 9:40 PM / IP Logged  

Have both remotes when programming.

find the brain, put dip switch #8 in the up/on postion.

Next, hit the brake pedal 1 time. The brain should react with clicks....

after that, hit unlock on both remotes, one after the other. The brain should react again with each remote button pushed.

When this is done, flip dip#8 into the down/off position, and hit the brake pedal. You should be done now!

char_hanson 
Member - Posts: 2
Member spacespace
Joined: May 07, 2009
Posted: May 11, 2009 at 8:36 PM / IP Logged  

I had already tried the Pin 8 trick.  It didn't work.

I just tried it again.  When I turn Pin 8 "ON" and press the brake, I do not hear anything from the "brain".

Any other suggestions?

KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: May 12, 2009 at 12:19 PM / IP Logged  

Check the receiver cable at both ends. Make sure it's plugged in properly. (at the receiver, and the brain)

Check to make sure the foot brake connection is solid as well.

This is how the procedure is done, it's in level 1 of the programming menu.

When you hit the brake with pin 8 up, does the led on the brain flash?

monzer4819 
Member - Posts: 1
Member spacespace
Joined: November 20, 2009
Location: Quebec, Canada
Posted: November 20, 2009 at 6:37 PM / IP Logged  
KarTuneMan wrote:

Have both remotes when programming.

find the brain, put dip switch #8 in the up/on postion.

Next, hit the brake pedal 1 time. The brain should react with clicks....

after that, hit unlock on both remotes, one after the other. The brain should react again with each remote button pushed.

When this is done, flip dip#8 into the down/off position, and hit the brake pedal. You should be done now!

I registered at this forum specifically for programming a Serie 120.   This advice I found here helped me reset my remote after a Lebeau dealer left it in "programming" mode.
However the above was not quite accurate for me:
Pressing the brake after flipping the 8 pin up canceled the whole process.
I had to flip the 8 dip up, press any key on my remote (unlock) and THEN press and hold the brake for 10 seconds (heard a click after 10 seconds) to "save" the changes.   Then 8 dip back off. Repeat:   I did not press the break until AFTER pressing a key on my remote.
Also the entire process only worked with my key in the ignition and set to "on" (engine was off).
Hope this helps and saves someone money like it did for me.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer