I’m looking for some assistance before I go and break something that will end up costing me more than this Security System and Remote Start.
For starters, I’d like to thank everyone’s posts on this site… I would be this far in the install if it wasn't for everyone here.
Problem description:
Remote Start works (with Relay) but with Major problems
Parking Lights won’t flash on arm/disarm of the security system
Hardware:
Viper 5904
PKALL
Relay SPST 30A
Park Light Jumper = (-) Negative
Wiring:
H1/1 Red ---> WHITE/ Red 12V/30A @ Ignition
H1/2 Black ---> Ground
H1/3 Brown ---> Siren (+)
H1/4 WHITE/ Brown ---> n/c
H1/5 White ---> Green @ Parking Light Switch
H1/6 Orange ---> n/c
H3/1 Pink ---> BLACK/ Red @ Ignition
H3/2 RED / White ---> WHITE/ Red 12V/30A @ Ignition
H3/3 Orange ---> WHITE/ Green @ Ignition (Accessory Output)
H3/4 Violet ---> GREEN/ Black (Car Side) @ Ignition
H3/5 Green ---> GREEN/ Black (Key Side) @ Ignition
H3/6 Red ---> WHITE/ Red 12V/30A @ Ignition
H3/7 Pink/White ---> Blue / YELLOW @ Ignition
H3/8 Pink/Black ---> n/c
H3/9 RED / Black ---> WHITE/ Red 12V/30A @ Ignition
H2/1 Pink/White ---> n/c Ignition
H2/2 BLACK/ White ---> Ground
H2/3 Blue/White ---> n/c 2nd Status/Rear Defogger
H2/4 GREEN/ Black ---> GREEN/ Black OEM Alarm Disarm
H2/5 RED / White ---> n/c Trunk
H2/6 Green ---> GREEN/ YELLOW Door Trigger
H2/7 BLACK / YELLOW ---> Blue Dome Light Trigger
H2/8 BROWN / Black ---> GREEN/ Red Horn
H2/9 Dark Blue ---> PKALL blue/white H2/3 Status Output
H2/10 Pink ---> n/c Ignition 1
H2/11 WHITE/ Black ---> n/c Aux3
H2/12 Violet ---> n/c Door Trigger Input
H2/13 WHITE/ Violet ---> n/c Aux1
H2/14 Violet/Black ---> n/c Aux2
H2/15 ORANGE / Black ---> n/c Aux4
H2/16 Brown ---> Blue Brake Shutdown Input
H2/17 Gray ---> Hood Pin
H2/18 Violet / YELLOW ---> BLACK/ White Starter Output
H2/19 Blue ---> n/c Trunk Pin
H2/20 Gray/Black ---> n/c Diesel Wait
H2/21 WHITE/ Blue ---> n/c Turbo Timer
H2/22 Orange ---> n/c Accessory output
H2/23 Violet/White ---> n/c Tachometer
H2/24 GREEN / WHITE ---> Violet OEM Alarm Arm
PKALL
D2D ---> Viper
H2/1 Violet/White ---> Light Green IMO ECM
H2/2 Yellow/Black ---> Blue/White (ECM Side) IMI ECM
H2/3 Blue/White ---> Viper H2/9 Dark Blue Status
H3/1 Light Green ---> Blue/White (ECM Side) IMI ECM
H3/2 ORANGE / Brown ---> Blue/White ( Car Side) IMI ECM
In the above configuration the remote starter engages accessory, but never turns over the engine with an error “Low Battery” (9 Flashes)
Next Step:
Starter Relay Wiring – Automotive SPST 30A
Viper H2/18 ---> 85
Tacoma Starter BLACK/ White ---> 30
12V (Fuse 30A) ---> 86 & 87
Result:
Remote Starter works, BUT engine light says ON and going from reverse to Neutral or Drive to Neutral kills the engine. Relay = Removed :)
Thanks a head of time for any and all reply’s and as I like to say “If everything just worked, then I wouldn't learn a thing.”
-Chad