the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Remote Start for 2016 Subaru Legacy Key Start ATM 4 Cylinders


Post ReplyPost New Topic
< Prev Topic Next Topic >
wyciwug 
Copper - Posts: 156
Copper spacespace
Joined: February 08, 2008
Location: Virginia, United States
Posted: December 10, 2018 at 2:18 PM / IP Logged Link to Post Post Reply Quote wyciwug
I will be using Idatalink ADS AL, Python 4105P as the remote start. Will be using Data mode. I do have some questions.
What exactly is E-Brake status and do I have to connect that wire from the Bypass to Remote start? Which wire on the R.S. to be used for this?
The vehicle called for 2 starter wires but RS has only 1, I still need to use relay for the second starter, right? A friend/tech told me to use Diodes.
thanks
dcd
geepherder 
Platinum - Posts: 3,668
Platinum spaceThis member consistently provides reliable informationspace
Joined: October 27, 2003
Posted: December 10, 2018 at 3:01 PM / IP Logged Link to Post Post Reply Quote geepherder
E-brake status should be negative when the emergency brake is applied. On manuals you connect this to the neutral safety/e-brake input. On an automatic you can just ground it.
Search the wiring section. There are 2 second starter wires listed, both negative.
Your system may have a negative starter output, so double check. I agree, use diodes.
My ex once told me I have a perfect face for radio.
kreg357 
Platinum - Posts: 7,802
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: December 11, 2018 at 6:52 AM / IP Logged Link to Post Post Reply Quote kreg357
If you are using the ADS AL-CA bypass module and going D2D with the 4105, make sure you flash the module with the DBI AL(DL) SUB3 firmware.
I would follow the Type 4 Install diagram in the SUB3 install guide. The Strater2 wire shown is (+). Unfortunately, the 4105s Pink/White selectable wire can't be set to Starter, so I would use a relay to convert the 4105s Purple (-) Starter wire to the needed (+) signal. Using diodes to isolate a 25 amp and a 10 amp circuit may not be a good idea.
Soldering is fun!
geepherder 
Platinum - Posts: 3,668
Platinum spaceThis member consistently provides reliable informationspace
Joined: October 27, 2003
Posted: December 11, 2018 at 7:13 AM / IP Logged Link to Post Post Reply Quote geepherder
Kreg is right. I just realized I was looking at the PTS in the wiring section, not key start. Diodes would be a bad idea.
My ex once told me I have a perfect face for radio.
wyciwug 
Copper - Posts: 156
Copper spacespace
Joined: February 08, 2008
Location: Virginia, United States
Posted: December 13, 2018 at 1:41 PM / IP Logged Link to Post Post Reply Quote wyciwug
Hello
I looked at the vehicle wiring diagram, I saw "Second starter RED (SS1); black (SS2) - push button ignition switch, black 14 pin plug, pin 7,2 < does this only avail in PTS, not Key start?
The 4105's Purple starter wire is (+)
dcd
kreg357 
Platinum - Posts: 7,802
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: December 13, 2018 at 5:24 PM / IP Logged Link to Post Post Reply Quote kreg357
Its possible you are making this more intriguing than it is. Flash the ADS AL-CA with the correct firmaware, download the install guide shown and follow the Type 4 install diagram.
The remote starter shown is generic so you will have to use the 4105 guide and programming to provide the needed outputs to complete the install.
Soldering is fun!

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer