Valet 562T Help 1996 Dodge Ram

Home / the12volt's Install Bay / Car Security and Convenience / Valet 562T Help 1996 Dodge Ram (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

gokeeper

Member - Posts: 20

Joined: December 24, 2003

Location: United States

Posted: January 06, 2004 at 5:15 PM / IP Logged

I bought a valet 562t Remote start But it does not say where to connect the STATUS OUTPUT, ACCESORY RELAY TRIGGER, IGNITION RELAY TRIGGER, OR STARTER RELAY TRIGGER. these wires are all (-) 200mA wires and i have no clue where they go i have hooked up every thing else and the door locks pulse and lights flash but the remote start will do nothing not even click.

Also the door locks pulse but do not unlock or lock the doors.. Its a 1996 dodge ram and i tested the wires there were voltage on theer when u press the door lock and unlock buttons... Itsa Dodge diesel if it makes a difference... Any help will be appreciated thanks ASAP...

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: January 06, 2004 at 5:27 PM / IP Logged

see if this info helps....also post a link for the unit you are installing....

Make: Dodge

Model: Pickup - Fullsize

Year: 1996

This Database Was Last Updated On: 6/9/2003

Index #: 2904

Alarm

Constant 12 volts RED & PINK/BLACK IGNITION SWITCH HARNESS

Ignition 12 volts D BLUE IGNITION SWITCH HARNESS

Starter D BLUE / YELLOW IGNITION SWITCH HARNESS

Dome Light YELLOW (-) DRIVER PIN SWITCH

Trunk Pin Switch N/A

Parking Lamp BLACK / YELLOW (+) AT HEADLIGHT SWITCH

Power Lock ORANGE / VIOLET IN BLACK CONNECTOR #203

Power Unlock PINK/VIOLET BEHIND PARK BRAKE

#203- See Reversal Rest At Ground Power Window Circuit Diagram.

Remote Start

Tach Signal GRAY/L BLUE AT POWERTRAIN CONTROL MODULE *

Ignition #2 BLACK/ ORANGE IGNITION SWITCH HARNESS

Ignition #3 N/A

Accessory BLACK/ WHITE IGNITION SWITCH HARNESS

Neutral Safety BLACK/ WHITE (-) AT SWITCH ON TRANSMISSION **

Brake Light WHITE/ TAN (+) AT SWITCH ABOVE BRAKE PEDAL

Reverse Light VIOLET/BLACK (+) AT SWITCH ON TRANSMISSION

Rear Window Defrost N/A

* Powertrain Control Module Located On Passenger Rear Of Engine On Firewall. ** BLACK/ WHITE (-) Wire Also Located At Powertrain Control Module.

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

gokeeper

Member - Posts: 20

Joined: December 24, 2003

Location: United States

Posted: January 06, 2004 at 5:31 PM / IP Logged

I have hooked those up this is an auxillary harness the vallet seams a little wierd to me the link is http://www.directed.com/guides/manuals/ig/valet/N562T_6-03.pdf that is the install manues the auxilery harnedd is off the relay satellite ( well that is what they call it) the remote start ill not even engage the accesory so far...

gokeeper

Member - Posts: 20

Joined: December 24, 2003

Location: United States

Posted: January 06, 2004 at 5:34 PM / IP Logged

one more thing if i groung STATUS OUTPUT, ACCESORY RELAY TRIGGER, IGNITION RELAY TRIGGER, OR STARTER RELAY TRIGGER. these wires are all (-) 200mA wires the starter and accerory and ignition will initiate but will not stop these wire must need to be connected to something but i'm not sure what.

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: January 06, 2004 at 9:43 PM / IP Logged

hey go,

my computer is running really slow right now......its taking for ever to load pages.... i will try again tomorrow to help you....

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

gokeeper

Member - Posts: 20

Joined: December 24, 2003

Location: United States

Posted: January 07, 2004 at 2:52 PM / IP Logged

i TALKED TO SOME TECH SUPPORT AND THEY SEAM TO THINK TEH UNIT IS BAD THE FIRST THAT THEY HAVE EVER HAD BAD IS WHAT THEY TOLD ME I FIND THAT HARD TO BELIEVE....

gokeeper

Member - Posts: 20

Joined: December 24, 2003

Location: United States

Posted: February 09, 2004 at 10:34 PM / IP Logged

does this ram have typpe c door locks so i need two relays right?

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: February 16, 2004 at 1:40 PM / IP Logged

this little 4 pin harness is only used to power 3rd ignition or 2nd crank or Acc relays...these are all low current negative out to active extra relays..in most installs you can throw this harness in a box and never use it..but only hook these wires up IF powering extra relays

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: February 16, 2004 at 1:41 PM / IP Logged

for door locks use a 451M module, it plugs right in

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Valet 562T Help 1996 Dodge Ram

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.