Install problem on 92 honda integra, japanese

Home / the12volt's Install Bay / Car Security and Convenience / Install problem on 92 honda integra, japanese (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 07, 2005 at 3:46 AM / IP Logged

I have a small problem with the install in the integra. Everything went in fine apart fromt eh central locking. but later that night the guy said he had a couple of problems

1st his left headlight wan't working (replaced Bulb Everythings OK)

2nd when in car his internal clock and Trunk open Light in the cluster seem to be flashing when you open the door they come on permanently. I checked my door trigger and boot trigger connections again they are fine. I temperarily remedied the problem Via the Boot light switch. when i turned it off all together. the clock and light on the dash went out. also when i turned it on or the dome light on they flashed with the other lights.

I'm pretty sure my connections are all good. the lights are flasking with the same interval as a turn signal but i can't hear any relays clicking

any Idea's (also i checked all the fuses in the Cab)

Also i don't think the alarm is at fault because problem persists with harness plugged out of brain.

ANy suggestions would greatly be appreciated

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: June 07, 2005 at 5:52 AM / IP Logged

you best choise use diodes and make sure the wires is not toching together

how own your mind, control your life.

MECP certified. always use a DMM

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 07, 2005 at 6:03 AM / IP Logged

cheersw for the input dare i checked that they where not touching together already.

where would i use diodes i'm not following you there.

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: June 07, 2005 at 6:54 AM / IP Logged

for some reason can be a back feed form the trunk or door trigger.

how own your mind, control your life.

MECP certified. always use a DMM

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 07, 2005 at 6:59 AM / IP Logged

so i basically put a diode on the door trigger wire silver stripe facing the switch. and same with the trunk

just to block negative current from going back to the switch

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: June 07, 2005 at 7:03 AM / IP Logged

yes.

how own your mind, control your life.

MECP certified. always use a DMM

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 07, 2005 at 7:06 AM / IP Logged

ok i'll give that a try later. worth a try anyway.

weird problem i never came across anything like it. I plugged the harness out of the brain and problem still occurs. and the flashing.

I'll try that anyway dare thanks.

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 07, 2005 at 12:03 PM / IP Logged

this has been doing my nut in the last couple of days then something hit me today

i took the drivers door switch out to check the colour of the wire. the car is old and when i put the screw back in it could have been a bad earth then. what do you reckon guys could this be it. if not i will go with the above suggestion

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 08, 2005 at 9:41 AM / IP Logged

ok i'm going back to try this integra in a couple of hours.

The only thing i can think mihg thave caused the problem is the door pin not earthing right. any suggestions or other possible causes beore i try fix it.

I will prost my findings anywho

Powermyster

Silver - Posts: 962

Joined: April 06, 2005

Location: Ireland

Posted: June 08, 2005 at 9:41 AM / IP Logged

ok i'm going back to try this integra in a couple of hours.

The only thing i can think mihg thave caused the problem is the door pin not earthing right. any suggestions or other possible causes beore i try fix it.

I will post my findings anywho

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.