the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

bulldog deluxe 200b remote start 1990 accord


Post ReplyPost New Topic
< Prev Topic Next Topic >
aj_aj 
Member - Posts: 5
Member spacespace
Joined: April 10, 2007
Location: United States
Posted: April 13, 2007 at 11:41 PM / IP Logged  

hi there

as I said i have bulldog deluxe 200b 2way remote starter I want to put it on 1990 honda accord but i don't know if my accord has any anti-theft system, any how alarm bypass module (IF114) came with it do I need to connect it too,it says bypass anti-theft system so i don't know if i should install it or not?

if you are familiar with this system please let me know what to do

thanks

wlmpwlmp 
Copper - Posts: 59
Copper spacespace
Joined: December 20, 2006
Location: Canada
Posted: April 14, 2007 at 6:46 AM / IP Logged  

No factory anti-theft on this car. Heres the info you need to do the install tho....

 MODEL YEAR(S)
 ACCORD  1990 -1993
 KEY T-HARNESS IMMOBILIZER
  N/A   HON-2   N/A
 PART  COLOR LOCATION DIAGRAM
 12 VOLT CONSTANT  WHITE (+)   IGNITION SWITCH HARNESS   
 STARTER BLACK/ WHITE (+)  IGNITION SWITCH HARNESS   
 STARTER 2 N/A   
 IGNITION 1 BLACK / YELLOW (+) IGNITION SWITCH HARNESS  
 IGNITION 2 N/A    
 IGNITION 3 N/A     
 ACCESSORY /HEATER BLOWER 1 YELLOW (+)  IGNITION SWITCH HARNESS   
 ACCESSORY /HEATER BLOWER 2 N/A     
 KEYSENSE N/A     
 PARKING LIGHTS ( - ) N/A     
 PARKING LIGHTS ( + ) RED / BLACK (+)  @ FUSEBOX IN DRIVERS KICK PANEL   
 POWER LOCK BLACK/ WHITE (TYPE B)  LOW IN DRIVERS KICK PANEL   
 POWER UNLOCK BLACK/ RED (TYPE B)  LOW IN DRIVERS KICK PANEL   
 LOCK MOTOR WIRE N/A     
 DOOR TRIGGER BLACK/ WHITE (-),  @ BROWN PLUG LEFT of STEERING COLUMN   
 DOMELIGHT SUPERVISION USE DOOR TRIGGER, Requires Part #775 Relay     
 TRUNK RELEASE N/A     
 SLIDING POWER DOOR N/A     
 HORN LIGHT GREEN/ BLUE (-)  @ STEERING COLUMN HARNESS   
 TACH BLUE  @ DISTRIBUTOR   
 WAIT TO START LIGHT N/A     
 BRAKE GREEN / WHITE (+)  @ SWITCH ABOVE BRAKE PEDAL   
 FACTORY ALARM DISARM  N/A     
 ANTI-THEFT N/A     
NOTES
 

WesMan
aj_aj 
Member - Posts: 5
Member spacespace
Joined: April 10, 2007
Location: United States
Posted: April 14, 2007 at 7:23 PM / IP Logged  

thanks wesman but i have this sheet and I did connect all these wires still won't start I got the doors to lock and unlock  tho ,but the starter won't work I looked for another sheet and it said there is a 2  IGNITION  wire so I connected  now I can hear there is a click when I push start button,but still won't work what else I can do to make it work,

so as you said this car does not need any bypass?right

thanks for looking

wlmpwlmp 
Copper - Posts: 59
Copper spacespace
Joined: December 20, 2006
Location: Canada
Posted: April 15, 2007 at 8:39 AM / IP Logged  
did you hook up the tach wire? if so did you program that tach? check page 30 or your book, diagnostics section and do what it says there. report back how many flashes you get out of that led built into the starter brain. also did you install the safety shutdown toggle switch? if so try flipping it to the other position and try the R/S now!
WesMan
wlmpwlmp 
Copper - Posts: 59
Copper spacespace
Joined: December 20, 2006
Location: Canada
Posted: April 15, 2007 at 8:45 AM / IP Logged  

if your unit did not come with that toggle im talking about, then what did you connect the grey wire(safety shutdown) wire to? if it is hooked to ground then the starter wont start. the wire is supposed to be hooked to a hoodpin, so when the hood is up the brain will see ground and prevent accidental starting for you or say a mechanic who is under the hood.  if you did just hook that grey wire to ground then un hook it from that ground and then try to start. 

WesMan
aj_aj 
Member - Posts: 5
Member spacespace
Joined: April 10, 2007
Location: United States
Posted: April 15, 2007 at 7:06 PM / IP Logged  

I did  not connect the tach cuz it says if you want to program the feature IV-2 to (engine checking tach) otherwise do not connect this wire and tape the end.page 16 manual.

and I did not connecet the safety switch  it says optional but if i need that I will connect it.

but there is one more wire I can not find the horn wire it says (light GREEN/ blue ) and I can not find that how ever I found light GREEN/ black is that the same wire(STEERING COLUMN HARNESS ) if not where can I find it.

thanks wesman

monkies 
Member - Posts: 13
Member spacespace
Joined: March 02, 2007
Location: United States
Posted: April 16, 2007 at 11:31 AM / IP Logged  
Did you connect the small black wire on the H4 to ground?
What does it do when you press the start button twice? does the remote beep 3 times?
if h4/2 (thin black) is grounded and you still get the 3 beeps, then it might be a glitch in the unit. what you have to do it put it in tach mode then exit programming mode then put it back into engine checking voltage (tachless) and then it should start. I've seen alot of these units end up in a "limbo" mode that wasn't tach or tachless that usually takes care of the problem
aj_aj 
Member - Posts: 5
Member spacespace
Joined: April 10, 2007
Location: United States
Posted: April 16, 2007 at 6:52 PM / IP Logged  

yes I did connect that black wire from H4 to the ground. and I still can not find the horn's wire . the thing is I can not program it I did what the book says but still can not program it  I dont know what to do with it, if you have an easy way to do it (programming)please let me know.

thanks wesman for your help

monkies 
Member - Posts: 13
Member spacespace
Joined: March 02, 2007
Location: United States
Posted: April 19, 2007 at 12:32 PM / IP Logged  
Well make sure the remote control says the doors are unlocked (even if you don't have the door locks hooked up)that will keep you from entering program mode. You will need the horn to program if you can't find the horn wire use your test probe and look for a negative pulse on the horn wire on the unit instead of listening for the "chrip"
aj_aj 
Member - Posts: 5
Member spacespace
Joined: April 10, 2007
Location: United States
Posted: April 21, 2007 at 4:13 PM / IP Logged  

thanks man

I will try that too and I hope its going to work this time .I will let you know

thanks again


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer