voltage stabiliser

Home / the12volt's Install Bay / General Discussion / voltage stabiliser (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

fastwheel

Member - Posts: 3

Joined: July 01, 2004

Location: Singapore

Posted: September 24, 2004 at 8:55 AM / IP Logged

I want to built and install voltage stabiliser on my Matrix.I need schematic drawing and what are the components use to design one.There some in the market on sale like XCS or Hyper voltage stabiliser.

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: September 24, 2004 at 5:29 PM / IP Logged

You are referring to a regulated power supply which will output a constent 12 volt power souce?

Regards

EVIL Teken . . .

dxav

Silver - Posts: 314

Joined: September 11, 2002

Location: United States

Posted: September 24, 2004 at 11:21 PM / IP Logged

Yeah, I was going to ask the same question as Teken, but didn't want to sound dumb. What is the application? What is your estimated current draw? I can build you a PCB with the regulator.... (I have done a few PS2 mods lately, and have a few other boards)

PM if you need....

DXAV

fastwheel

Member - Posts: 3

Joined: July 01, 2004

Location: Singapore

Posted: September 26, 2004 at 10:22 AM / IP Logged

Hi Guys,

If it is a regulated power supply maybe you can show me the pcb arrangement with the necessary components.Below is a detail decription from Hyper Voltage System.

Detail Description:

Hyper Voltage System – Type MR – Multi rance rev. perofrmance with increase of both horsepower and torque

The Hyper Voltage System Type MR is to stabilize the flow of the voltage from the battery. By stabilizing the voltage from the battery, the load on the battery is reduced, resulting in increasing engine performance and electrical equipment. Type MR specialize sport driving and high rev. performance with increase of horsepower.

Type MR Hyper Voltage System Effectiveness and Feature:

- Increase Torque

- Increase Horsepower

- Better Throttle Response

- Better Fuel Mileage

- Increase efficiency of electrical equipment

- Simple, easy installation

- Can be install in any cars, trucks, and SUVs

Regards,

dxav

Silver - Posts: 314

Joined: September 11, 2002

Location: United States

Posted: September 26, 2004 at 2:26 PM / IP Logged

The board I use for the PS2 mods is shown below. The PCB manufacturer is Nightfire, they get the credit, I just modified it for higher current applications (the PS2 draws 3A @ 12VDC). I do have a few left.

This is used because the PS2 requires 12VDC. A car battery can fluctuate from 10.4V all the way up to 14.8 depending on the load-- and sometimes even more.

Is this what you are looking for?

DXAV

fastwheel

Member - Posts: 3

Joined: July 01, 2004

Location: Singapore

Posted: September 28, 2004 at 6:52 AM / IP Logged

Well, not sure yet.Do you have a schematic drawing indicating the components value.Anyway thanks for the photo.

Regards,

dxav

Silver - Posts: 314

Joined: September 11, 2002

Location: United States

Posted: September 28, 2004 at 9:14 AM / IP Logged

Well, fastwheel. Depending on the regulator you choose, the components are detailed in the datasheet fot the part. Goto www.digikey.com type in LM1084 (or whatever regulator), then there is a link to the datasheet. It will show you the common configuration for parts and the appropriate values. I usually use a 10uF on the Vin, and a 33uF on the Vout. Another 0.1uF cap can be used to decouple the regulator, reducing noise on the lines. It's simple. Just remember the 10 and 33uF caps need to be polarized or Tantalum type.

DXAV

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

voltage stabiliser

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.