2004 pontiac aztek remote start

I have a valet 562T remote start that i want to install on a 2004 pontiac aztek with keyless entry and GM's passkey III anti-theft security system. i looked up the wiring diagram for my car and it is listed like this:     INSALLATION WIRING GUIDE - Pontiac / Aztek / 2004 / All Info Item       Wire Color     Pol           Wire Location 12volts    orange          +           Ignition harness starter     yellow            +           Ignition harness second starter            N/A       ignition   pink+           Ignition harness second ignition   green             +           Ignition harness 3rd ignition            N/A accessory             orange           +           Ignition harness second acc          brown             +           Ignition harness keysense   lt.green        -           Ignition harness power lock RED / black       -            pink plug @ BCM notes: lock requires a negative trigger thur a 470 ohm resistor. unlock requires a straight negative trigger. the BCM is located at the front of the center console under the radio. power unlock            same wire as power lock lock motor              gray           5wi           back of fuse box.         black plug unlock motor            tan            5wi       " disarm defeat           tan            5wi       " parking lights+        do not use parking lights-        lt.blue        -             headlights switch headlightyellow        -             headlights switch reverse light           lt.green       +        back fusebox blk plug door trigger            blue/white     -pink plug @ BCM dome supervision        use door trigger trunk/hatch pin        pink/black     -pink plug @ BCM trunk/hatch release     WHITE/ black    -            16pin grayplug@bcm factory alarm disarm    purple        -pink plug @ BCM tachometer              purplr/white   ac ignition coil speed sense             green          4K            16pingrayplug@bcm brake wire              white          +             brake pedal swtch parking brake           ORANGE / black   -pink plug @ BCM horn trigger            black          -steering column wipers             green(L),purple(H) +steering column Immobilizer bypass        required:Yes       type: PASS-Key III I hope this info helps some of you guys who had trouble finding the wiring info. i have a few questions about this list.on the disarm defeat polarity column it says 5wi what does this mean? and on the wipers wire color column it says green(L),purple(H) what does the (L) and the (H) mean? thanks for the help i am not a newbie but i have never installed a remote start before, only car alarms and radios and amps.get r done!!!!!!!

don't worry about the "disarm defeat", won't use it. IF you have a factory alarm you'll use the "factory alarm disarm". and why are you wanting to connect to the wipers? L= low H=high

cool i got the remote start working with no problems the only thing that i got left to do is to hook up the door locks the 2004 pontiac aztek has a 1 wire negative door trigger the wire color at the BCM is RED / black i have a ALA-DL1 programmable relay pack but i have no idea how to hook this thing up. if anyone knows how to get the lock/unlock funtion to work on a 2004 aztek with factory keyless entry i would be really grateful. thanks for the help in advance.get r done!!!!!!!

you already have it power lock RED / black       -            pink plug @ BCM notes: lock requires a negative trigger thur a 470 ohm resistor. unlock requires a straight negative trigger. the BCM is located at the front of the center console under the radio. power unlock            same wire as power lock

yea i have the wire colors and location but i have never installed an alerm or remote system on a car with a single wire negative door trigger system. i dont know how to wire the relays and where to put the resistor at?if anyone knows how to get the lock unlock working on a azntek with factory keyless and a valet 562T remote start please help i tried hooking the green and blue wires (the lock unlock wires)on the 562T straight to the blue/white wire at the bcm and on the one i put the resistor on the wire and all it would do is make a sound like it was unlocking or locking but the lock swtich didnt move at all just the noise.so i am thinking i need to add some relays to the setup?get r done!!!!!!!