the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

03 trailblazer no start

Home / the12volt's Install Bay / Car Security and Convenience / 03 trailblazer no start (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
chev104275 
Gold - Posts: 1,427
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: May 28, 2009 at 8:12 AM / IP Logged  
has anyone heard of this i have a 2003 chevy trailblazer wont start with key it doesnt have a remote start in it    when i turn the key to the start nothing happens doesnt try to start    the dash lights up like it usually would \ checked fuses none blown     
Thanks in adavnce Joe
If i Can't Install it    I Don't need it   Joe
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: May 28, 2009 at 8:46 AM / IP Logged  
Check the battery to make sure that it's properly charged. Next, check the starter relay or fuse in the engine compartment fuse panel with a DMM. What happened prior to the truck not starting, any information will help us.
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
chev104275 
Gold - Posts: 1,427
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: May 28, 2009 at 10:08 AM / IP Logged  
ok fuses are good no symtoms before the problem just wouldnt start last night and again this morn   if i play with the ing and tap on the column i can get it to start
If i Can't Install it    I Don't need it   Joe
ckeeler 
Gold - Posts: 1,461
Gold spacespace
Joined: June 20, 2008
Location: New Mexico, United States
Posted: May 28, 2009 at 11:08 AM / IP Logged  
it's most likely a worn out lock cylinder. it's causing the passlock to not work properly, thus you get a no start condition.
chev104275 
Gold - Posts: 1,427
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: May 28, 2009 at 11:21 AM / IP Logged  
kinda what i was thinking   do i need a scan tool to replace the ing cyl if not how do i code the existing key to the cyl
If i Can't Install it    I Don't need it   Joe
icearrow6 
Copper - Posts: 497
Copper spacespace
Joined: February 02, 2009
Location: California, United States
Posted: May 28, 2009 at 12:24 PM / IP Logged  
bypass module would let you use normal key to start. By normal I meant with out the built in "chip".
The worn out cylinder is the ACTUAL problem though.
joch1314 
Copper - Posts: 301
Copper spacespace
Joined: March 25, 2008
Location: Texas, United States
Posted: May 28, 2009 at 2:57 PM / IP Logged  

Those ignition cylinders seem to be a little more frail than most, especially if you have a lot of keys and/or keychains.  the extra weight pulls on the ignition cylinders and causes it to fail....kind of gay if you ask me, but that's GM for you.  My sister has a ton of keychains and i'm just waiting for her to have the same problem you are.....already told her about this prob too. 

...half of the truth can be worse than a lie. <----Roger Russell said that..
chev104275 
Gold - Posts: 1,427
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: May 28, 2009 at 3:09 PM / IP Logged  
ok thanks guys   but do i need a scan tool or a dealer after i install the cyl for any reason ??
If i Can't Install it    I Don't need it   Joe
chev104275 
Gold - Posts: 1,427
Gold spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: November 26, 2007
Location: Massachusetts, United States
Posted: May 28, 2009 at 5:05 PM / IP Logged  
it was the ing Switch not the cyl
If i Can't Install it    I Don't need it   Joe

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, May 6, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer