1998 olds delta 88

Home / the12volt's Install Bay / Car Security and Convenience / 1998 olds delta 88 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

skipastaria

Member - Posts: 18

Joined: May 05, 2003

Location: United States

Posted: August 25, 2009 at 6:49 PM / IP Logged

i have an olds delta 88 1998 and the keyless entry does not work i put a new battery in it and still nothing how do i find and check the module that controls the door locks

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: August 26, 2009 at 9:24 PM / IP Logged

Do you have any interior controls for the locks?

commit your way to jehovah and he will act in your behalf. psalms 37:5

tommy...

Gold - Posts: 1,901

Joined: December 10, 2004

Location: United States

Posted: August 26, 2009 at 9:31 PM / IP Logged

On some of the GM's ...After you replace battery...You have to press lock/unlock at the same time for 6-10 seconds...Not sure if that applies here...?!

M.E.C.P & First-Class

Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

tommy...

Gold - Posts: 1,901

Joined: December 10, 2004

Location: United States

Posted: August 26, 2009 at 9:45 PM / IP Logged

PROGRAMMING

Early 1999 Pontiac Grand am

1. Make sure ignition is in the OFF position.

2. Locate the Programming Connector in the trunk (driver’s side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access the connector.

3. The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure.

4. Press the LOCK and UNLOCK buttons on the transmitter simultaneously. In response, the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remote codes have been erased.

5. Repeat the previous step for each additional transmitter (including any existing transmitters). Do not remove jumper wire in between programming of transmitters.

6. Remove the jumper wire from the Keyless Programming Connector.

PROGRAMMING

2000 Pontiac Grand am

1. Close all doors.

2. Press and hold the Unlock button on door lock switch on drivers door.

Hold until instructed to release.

3. Insert and remove key from ignition 2 times. Do Not turn ignition.

4. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

5. Release door lock switch on drivers door panel.

A Chime will sound 3 times indicating that you are in programming mode.

6. Press both the Lock and Unlock buttons on the remote up to 30 seconds.

A chime will sound 2 times if remote has programmed successful.

7. Repeat step 6 if you are programming additional remotes.

8. Remove key from ignition to exit programming mode

programming instructions

2002 2003 2004

the manufacturer’s programming instructions for your vehicle make model and year specify diagnostic programming required

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment

M.E.C.P & First-Class

Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

tommy...

Gold - Posts: 1,901

Joined: December 10, 2004

Location: United States

Posted: August 26, 2009 at 9:46 PM / IP Logged

PROGRAMMING INSTRUCTIONS

1996-1997 Aurora

1.Turn ignition OFF

2.Access DATA LINK CONNECTOR (DLC) , next to steering column

3.Use fused jumper wire, jump connectors 4 & 8 in DLC

4.Turn ignition to ON

5.To PROGRAM…

6.…Press and hold LOCK & UNLOCK remote buttons at same time

7.…Doors will lock and unlock to let you know the remote has been programmed

8.Repeat steps 6 & 7 for additional remotes

9.Take jumper wire our to exit programming mode

- Additional functions and feedback settings can be set to respond to the remote transmitters – see dealer

PROGRAMMING INSTRUCTIONS

1998-1999 Aurora

1.Turn ignition OFF

2.Access DATA LINK CONNECTOR (DLC) , next to steering column

3.Use fused jumper wire, jump connectors 4 & 8 in DLC

4.Close all doors

5.Turn ignition to ON

6.Doors will lock

5.To PROGRAM…

6.…Press and hold LOCK & UNLOCK remote buttons at same time for 30 seconds

7.…Doors will lock and unlock to let you know the remote has been programmed

8.Repeat steps 6 & 7 for additional remotes

9.Take jumper wire our to exit programming mode

Still looking to find remote programming for you...!

M.E.C.P & First-Class

Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

skipastaria

Member - Posts: 18

Joined: May 05, 2003

Location: United States

Posted: August 29, 2009 at 8:18 AM / IP Logged

yes there are interior controls

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1998 olds delta 88

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.