2007 lincoln, python won't crank

Home / the12volt's Install Bay / Car Security and Convenience / 2007 lincoln, python won't crank (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

f150_4x4er

Member - Posts: 5

Joined: November 09, 2006

Location: United States

Posted: October 17, 2009 at 5:34 PM / IP Logged

Hello, i have installed a Pyton 1401 in my 2007 Lincoln Mark lt, I am not using the system for locking and unlocking doors or any accesories, just remote starting. Problem is when i push the start button on the remote it powers up, parking lights flash, dash lights come on but will not crank. I have check that the Neutral safety swich is grounded and the hood pin is not grounded. Everything else checks out OK other than i am not getting power for the RS module to the Violet wire which is the starter wire from the module. I am using a XpressKit PKFM but even if that is faulty it should not prevent it from cranking...would it. Any help would be much apprieciated as the interior of my truck is in pieces right now. THANKS!

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: October 17, 2009 at 6:27 PM / IP Logged

if the bypass is faulty, it wont crank, fords dont crank when the anti theft isnt bypassed, check to see if the theft light is blinking

f150_4x4er

Member - Posts: 5

Joined: November 09, 2006

Location: United States

Posted: October 17, 2009 at 6:39 PM / IP Logged

it is blinking the same pattern as the security light, but not at the exact same time.

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: October 17, 2009 at 6:43 PM / IP Logged

does it blink on the dash when you try remote start

f150_4x4er

Member - Posts: 5

Joined: November 09, 2006

Location: United States

Posted: October 17, 2009 at 7:31 PM / IP Logged

light on dash blinks rapidly, while the bypass module stays lit solidly.

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: October 17, 2009 at 8:10 PM / IP Logged

bypass isnt hooked up right or its not programmed

f150_4x4er

Member - Posts: 5

Joined: November 09, 2006

Location: United States

Posted: October 17, 2009 at 8:15 PM / IP Logged

I also tried remote starting it with the key in the ignition, and it did not crank. What should the led be doing if the bypass module is connected and programmed promperly ?

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: October 18, 2009 at 9:03 AM / IP Logged

Battery LIGHT GREEN/ VIOLET (+) IGNITION SWITCH HARNESS

Ignition 1 DK BLUE/LT GREEN (+) IGNITION SWITCH HARNESS

Accessory 1 BLACK/ LIGHT GREEN (+) IGNITION SWITCH HARNESS

Starter 1 RED / LIGHT BLUE (+) IGNITION SWITCH HARNESS

i mean its a pretty easy truck, im pretty sure most of us could do it under an hour......

you have all the connections correct?

are they good connections?

is the remote start programmed right?

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: October 18, 2009 at 10:18 AM / IP Logged

I don't have anything to contribute to this post that would assist the orignial poster, but mr metz, i just wanted to let you know that fords do crank even though the antitheft isn't bypassed, unless of course the antitheft specs on fords in the U.S are different, .

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: October 18, 2009 at 10:45 AM / IP Logged

No they don't crank. They sit there with ignition on and time out until retry

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.