viper 5701 remote programming

Home / the12volt's Install Bay / Car Security and Convenience / viper 5701 remote programming (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 03, 2009 at 10:59 AM / IP Logged

1993 Sentra GXE

I installed th Viper 5701 in my 1993 Sentar GXE- experiencing the following issue:

Step 3 - Getting into Automatic Transmission Mode for Remote Start Function-

Need to change to Automatic Transmission from default Manual Mode
When I press and hold the valet switch (per Automatic/Manual Programming) the LED does not flash 3 times (no flashes at all) Siren chirps 3 times (no chirps at all)
The alarm functions of arm and disarm work - Remote Learn (Default Setup) completed succesfully - alarm sounds etc.

Any help would be appreciated

Thanks for your help

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: November 03, 2009 at 11:17 AM / IP Logged

are you into menu 3? item 1 i think? these units are a real PITA to program without a Bitwriter.....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 03, 2009 at 1:16 PM / IP Logged

The trouble I am having is accessing menu 3 to change from Manual to Automatic.

Any ideas on how I can get into menu 3

Thanks for the reply

Thanks for your help

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: November 03, 2009 at 6:35 PM / IP Logged

Is your door trigger wire connected? It really is simple to program, but everything must be functional first!

syl20rochon

Copper - Posts: 298

Joined: October 16, 2009

Location: Ontario, Canada

Posted: November 04, 2009 at 5:54 PM / IP Logged

Door pins need to be connected cause the brain needs to see the door open, then turn ignition on the back off, press the switch until you hear 3 chirps, then release the button then press again and hold, you'll hear 1 chirp...while holding down the switch, press the unlock button on the remote, you'll hear 2 chirps that confirms automatic mode...release the switch and wait 5 to 15 seconds until you hear a long chirp, it mean that you have exited the program mode. You're done. Good luck.

Sylvain Rochon

MECP security specialist

Tech support for remote starters

26 Years of experience counts

I'm here to help.

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 04, 2009 at 8:25 PM / IP Logged

Thanks for the information

I will work through your instructions and let you know how it works out.

Thanks again

Thanks for your help

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 04, 2009 at 8:26 PM / IP Logged

Thanks for helping out- will check the door trigger

Thanks for your help

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 06, 2009 at 2:19 PM / IP Logged

I verified the wiring and worked through your instructions.

I was able to enter the programming mode and switch to automatic Transmission from the default of Manual- easy to program once you get have the steps to follow.

Remote start will still not engage- Any ideas?

Thanks

Thanks for your help

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: November 06, 2009 at 4:06 PM / IP Logged

did you ground the NSS wire? do you have the toggle switch plugged in? both are required to allow R/S to engage.....

does it try to start? if not, how many light flashes do you get?

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

wgrassie

Member - Posts: 8

Joined: November 03, 2009

Location: Ontario, Canada

Posted: November 09, 2009 at 9:37 AM / IP Logged

When I engage the Remote Start function, I get 1 Parking Light Flash
After trying to Remote Start- I tried to start the car with the key,
the car will not start until I toggle the Remote Start switch to the off position.

Any thoughts?

Thanks

Thanks for your help

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

viper 5701 remote programming

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.