1988 mustang viper 211hv wiring?

I am having trouble with the wiring for the viper 211hv system. I am installing the system in a 1988 ford mustang with factory power locks. I have done the following wiring so far. I have connected the pink / YELLOW and pink/lt green wires coming from the passenger side to the H1/6 and H1/17 respectively. (note: the passenger side is the master or where the 12v signal comes from) I then connected the drivers side pink / YELLOW and pink/lt green to the H1/5 and H1/8 respectively. I wanted to know what I do with the fused H1/7 & H1/9 combined wire and how to get the key fob to work? The door switches on both sides function in both the lock and unlock positions. The module also clicks and flashes the LED when pressing the lock button. It also clicks when pressing the unlock feature and stops the led flash. H1/1 Red - Yellow constant +12V H1/5 GREEN/ Black - pink / YELLOW H1/6 WHITE/ Black - pink / YELLOW H1/8 Blue/Black - Pink/ light green H1/17 BROWN / black - Pink/light Green H1/11 Black - chassis ground H1/15 Yellow - RED / Light Green Switched +12v Viper 211HV primary harness (H1, 12-pin connector 1988-89 Ford Mustang Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+     Yellow      Ignition Switch Harness Starter      WHITE/ Pink      Ignition Switch Harness Ignition      RED / Light Green      Ignition Switch Harness Accessory      Gray / YELLOW      Ignition Switch Harness Tach              Dark GREEN/ YELLOW      Coil Neutral Safety Wire      Not Grounding      OEM Switch opens Starter Circuit Brake Switch      RED / Green      Brake Switch Trunk Release      Purple / YELLOW (+)      Switch in Dash Trunk Pin      n/a      Works with Dome Light Parking Lights      Brown      Light Switch Head Lamp      RED / Yellow (+)      Light Switch Hood Pin      n/a       Factory Disarm      n/a       Door Trigger      BLACK/ Light Blue      Pin Switch or Courtesy Light Door Lock      Pink / YELLOW      Driver's Kick Panel or behind left Front Speaker Door Unlock      Pink/Light Green      Reverse Polarity Horn Wire      Yellow/Light Green (-)      Steering Column Windows Up      LF=Yellow, RF=Yellow/Black, LR=Yellow/Light Blue, RR=Yellow/Black Windows Down      LF=WHITE/ Black, RF=RED / Black, LR=RED / Light Blue, RR=RED / Black 1988-89 Ford Mustang Alarm, Remote Starter, Keyless Entry Wiring Information

This seems hopeless. I have tried wiring the module as per the instructions and still nothing. The most common wiring solution I could find is this: "WHITE/ black to lock switch GREEN/ black to lock motor BROWN / black to unlock switch blue/black to unlock motor and purple to whatever trigger you need (12v for positive trigger, ground for negative trigger)" I can't get it to work in any configuration. I have also tried to wire it per the bulldog instructions which are nearly identical to the viper instructions. When I connect the fused purple and PURPLE / black wires to ground it does nothing, when I connect said wires to a +12v source it pops the fuse. It doesn't matter how the lock and unlock wires are connected either, I can reverse them and it does the same thing. So what i have right now are working door lock switches and a keyfob that makes the viper module click.

Did you ever get this figured out? I am doing the same install on my '88 too. I've been trying to make heads and tails of this setup, right as I was starting to dig in I finally realized that the 211hv has built in relays. That sure changed things, should have read the instructions a bit closer. Anyway, I can't really give much advice as I was hoping this thread would be answered. However, I want to throw some things out for thought. I believe the Mustang does not have separate lock wires for the left and right side. So basically you can just wire up the driver side and it will control the passenger side too. I wonder if that might be a cause for some of your problems. My understanding of the wiring is the same as you put in your previous post. BROWN / Black to switch side of Pink/Light Green Blue/Black to actuator side of Pink/Light Green WHITE/ Black to switch side of Pink / YELLOW GREEN/ Black to actuator side of Pink / YELLOW Violet, Violet/Black to either +12v or ground. I am guessing for the Mustang it is for +12v but I honestly have no clue. I am trying to figure out if there is a typo in the installation guide. The WHITE/ Black and Violet/Black are both supposed to be wired to 87, shouldn't the WHITE/ Black be 87A? Those are just some of my thoughts and questions, hopefully someone might chime in soon. I am getting very eager to get this thing installed.

Have any of you tested to verify that you do indeed have the actuator motor wires and what polarity they rest at? It's farly simple once you have discerned the type of locking system in the vehicle! I will see if i can locate a diagram to assist!commit your way to jehovah and he will act in your behalf. psalms 37:5

That is a rest at ground system, wire just as stated in my previous post!commit your way to jehovah and he will act in your behalf. psalms 37:5

Thanks t&t! Hopefully I can get it wired up tomorrow.

Muhaha, it's alive! Well....sort of. If I wire it as posted above, pressing the lock button unlocks it and the unlock button locks and arms it. I had to reverse the wiring to: BROWN / Black to switch side of Pink / YELLOW Blue/Black to actuator side of Pink / YELLOW WHITE/ Black to switch side of Pink/Light Green GREEN/ Black to actuator side of Pink/Light Green Anyone know how difficult it would be to get the progressive locking to work when the locks don't have separate left and right wires? Thanks again for your help, I'm off to figure out how to wire the lights to flash.