remote start, 95 integra

Hey Guys, Im installing a viper 5101 and i was wondering if anyone could help me out. I know where all the wires are in the car but im not quiet sure which wires from the harness go to which ones in the car 1-Pink = Ignition 1 Input/Output 2-RED / White = (+) (30A) Fused Ignition 2 / Flex Relay Input #87 3-Orange = Accessory Output 4-Violet = Starter Output 5-Red = (+) (30A) Fused Ignition 1 Relay Input 6-Pink/White = (+) Ignition 2 Flex Relay Output 7-Pink/Black = 87a Of Ignition 2 Flex Relay 8-Red Black = (+) (30A) Fused Accessory/Starter Relay H1/1- RED / WHITE (-) 200mA AUX/TRUNK OUTPUT H1/2- RED (+) 12DC CONSTANT INPUT H1/3- BROWN (+) SIREN OUTPUT H1/4- WHITE/ BROWN PARKING LIGHT ISOLATION WIRE pin 87a on onboard rly H1/5- BLACK (-) GROUND H1/6- VIOLET (+) DOOR TRIGGER INPUT H1/7- BLUE (-) TRUNK PIN/ INSTANT TRIGGER INPUT (N/C N/O) H1/8- GREEN (-) DOOR TRIGGER INPUT (N/C N/O) H1/9- BLACK/ WHITE (-) 200mA DOME LIGHT SUPERVISION OUTPUT H1/10- WHITE/ BLUE (-) REMOTE START/TURBO TIMER ACTIVATION INPUT H1/11- WHITE PARKING LIGHT OUTPUT H1/12- ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT H2/1- LHT GRN/BLK (-) 200mA OEM ALARM DISARM OUTPUT H2/2- ORG/BLK (-) 200mA AUX 4 OUTPUT H2/3- GRN/WHT (-) 200mA OEM ALARM ARM OUTPUT H2/4- VIOL/BLK (-) 200mA AUX 2 OUTPUT H2/5- WHT/BLK (-) 200mA AUX 3 OUTPUT H2/6- WHT/VIOL (-) 200mA AUX 1 OUTPUT H2/7- GRY/BLK (-) 200mA DIESEL WAIT TO START (dont think we need this one LOL) H2/8- BRW/BLK (-) 200mA HORN HONK OUTPUT H2/9- VIOL/WHT TACHOMETER INPUT H2/10- DRK BLU (-) 200mA STATUS OUTPUT H2/11- PINK/WHT (-) 200mA FLEX RELAY CONTROL OUTPUT H2/12- ORG (-) 200mA ACC OUTPUT H2/13- PRPL (-) 200mA STARTER OUTPUT H2/14- PINK (-) 200mA IGNITION 1 OUTPUT H2/15- GRY (-) 200mA HOOD PIN INPUT (N/C N/O) H2/16- BLU/WHT (-) 200mA 2ND STATUS/REAR DEFFOGER OUTPUT H2/17- BRW (+) BRAKE SHUTDOWN INPUT H2/18- BLK/WHT (-) NEUTRAL SAFETY INPUT like where does the remote start input go to? Do i need all these wires? Like i said i know where the location is if someone could just write which color goes to which wire in teh car for me that would be great So my question is what colors go together from the harness to the car? MY Car is a 95 Acura INtegra

ALARM                                   CAR

PINK                                 BLACK / YELLOW

RED / WHITE                        WHITE

ORANGE                             YELLOW

VIOLET                          BLACK/ WHITE

RED                                       WHITE

PINK/WHITE                   WHITE/ BLACK

PINK/BLACK                          UNUSED

RED / BLACK                           WHITE

On the H1 harness you will only need a few wires

Red - Constant twelve

black-Ground

Browm- Siren

White- RED / green (car)

Green- GREEN/ red

No need for the harness under the h1 harness!

On the last harness the only wires you need are the

grey-  hood switch

brown- GREEN / WHITE (car)

BLACK/ white- ground.

commit your way to jehovah and he will act in your behalf. psalms 37:5

so everything is connected like this and it turns the car on like power wise all the blowers and electronics turn on but the engine does not start

Clutch switch if manual?

jdmtegg wrote: so everything is connected like this and it turns the car on like power wise all the blowers and electronics turn on but the engine does not start

What happens?

Also, did you use a meter to test or did you just connect as per the diagram?

commit your way to jehovah and he will act in your behalf. psalms 37:5

its not the clutch i ruled that one out because i sat in teh car and held in the clutch and it didnt work Teh red and black have power. and no i didnt use that meter to test but im positive the wires are correct could it be the programing of the remote

How are you positive if you didn't test? Do you have a meter?commit your way to jehovah and he will act in your behalf. psalms 37:5

does it even attempt to start???