4runner viper 5701

Toyota 4Runner 2008 WIRE        COLOR        LOCATION    POL. Battery 1 WHITE/ Blue Ignition Harness Positive Battery 2 Red Ignition Harness Positive Ignition 1 BLACK/ Red Ignition Harness Positive Ignition 2 Blue / YELLOW Ignition Harness Positive Starter 1 GREEN/ Black Ignition Harness Positive Accessory 1 WHITE/ Green Ignition Harness Positive Parklights Positive Green Trailer Connector Above Driver's Kick Panel Positive Parklights Negative Green At BECU Behind Fuse Box top Connector Negative Brake Lights GREEN/ YELLOW Trailer Connector Above Driver's Kick Panel Positive Horn GREEN/ Red Right Of Steering Column Gray Connector Negative Tach BLACK/ Orange (6) Above Gaz Pedal At The Top Blue Connector Lock Blue/White Driver's Kick Panel Door Harness 18 Pins Conn. Negative Unlock Blue/Orange (2) Driver's Kick Panel Door Harness 18 Pins Conn. Negative Trunk Same as Unlock Driver Door Unlock Green Driver's Kick Panel Door Harness 18 Pins Conn. Negative E-Brake Lt.Green At BECU Behind Fuse Box Middle Connector Negative OEM Hood Switch Pink/Green Driver Kick Panel In A Blue Connector Negative Disarm Green (3) Driver's Kick Panel Door Harness 18 Pins Conn (1) Negative Rearming Blue (4) Driver's Kick Panel Door Harness 18 Pins Conn. Negative Trunk Pin GREEN/ YELLOW Back Door ECU, Left Side Of Liftgate. Negative KeySense GREEN/ YELLOW At Key Switch In A 4 Pins Connector Negative Door Pin FL RED / Black At BECU Behind Fuse Box Middle Conn. Pin 23 Negative Door Pin RL Pink/Black At BECU Behind Fuse Box Middle Conn. Pin 11 Negative Door Pin FR RED / Yellow At BECU Behind Fuse Box Middle Conn. Pin 12 Negative Door Pin RR Pink/Blue At BECU Behind Fuse Box Middle Conn. Pin 24 Negative Rear Defogger GREEN/ Red At BECU Behind Fuse Box Middle Conn. Pin 1 Negative VSS PURPLE / Red ECM Behind The Glove Box AC Head Lights RED / White At BECU Behind Fuse Box top Connector Negative Auto lights OFF GREEN/ Orange At BECU Behind Fuse Box top Connector Open Windows Roll Up Yellow/Red + BLACK / YELLOW At BECU Behind Fuse Box Middle Conn (5) Windows Roll Down BLACK/ Blue + BLACK / YELLOW At BECU Behind Fuse Box Middle Conn (5) Moon Roof Tilt Gray At Roof Console Neagtive Moon Roof Open Lt.Green At Roof Console Neagtive Moon Roof Close Gray At Roof Console Neagtive Wiper Protection Blue At Wiper Switch Open BackUp Lights RED / Yellow At Connector Left Side Of Fuse Box Positive Transponder RX Pink/Green At Transponder Connector Pin 6 Data Transponder TX Lt.GREEN/ Red At Transponder Connector Pin 5 Data Comments : NOTE:This vehicle is equipped with a IMMOBILIZER passive anti-theft system. (1) To Disarm for Remote Start, send a ground while running on the keysensor wire, that will Disarm. (2) Need to pulse the WHITE/ Red (-) at the same time for Child Safety Lock Override. (3) First Pulse will Disarm Factory Alarm and Unlock Drivers Door. Second one will Unlock all Doors. (4) This wire will Lock all doors and Arm the Factory Alarm System. (5) To roll down the window, close contact between the BLACK/ Blue & BLACK / YELLOW, To roll up close contact between Yellow/Red and BLACK / YELLOW. (6) On some 4Runner, the tach signal is on a BLACK/ White above the BLACK/ Orange in the same Blue connector

This is a massive help. I owe you one. Thanks alot!!!!!!!ou812

your welcome and check your pm's

Also, will derected techs provide vehicle specific wiring diagrams for this alarm?  I was hoping they would. What I could really use is a specific diagram for which wires go where, is it just a t tap or cut and splice. any help? thanks muchou812

solder everything, only way to go i doubt that directed will give you any help with wireing if you are not a dealer

I am not a dealer, thats the problem, and I always solder and shrink wrap where I can. A portasol makes things alittle easier. Any pics would be great.ou812

Be advised the factory remotes are not going to work whenever you remote start this truck. You will have to use a key in the door. You may consider connecting the keyless wires on the 5701...Mike M2

Tech Manager

CS Dealer Services

there is a lot of help here. And i would say more knowledge about doing remotes starts and alarms than even DEI has on hand so don't be afraid to ask

agreed with monty.

DEI doesnt know all the problems and questions real DIY people have.

the can-sl2 will do the door locks for you through CANBUS.

if you need a wiring diagram, if you purchased your CANSL2 at a store, look for a small card (size of credic card), go to www.wirecolour.ifar.ca and type in the serial number for your car. Only selected bypasses have those, but if your a dealer you get infinate number of them.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert