missing ignition/accessory wire

I am installing a mars-33 remote start and alarm on my 2004 dodge ram 1500. it is a v-6 with no chip in the key and no power locks or windows. it starts fine with the remote but the abs light is lit(not sure if this is actually a problem). the radio and blower work but not the a/c compressor. It seems to me like have failed to energize 1 accessory wire and 1 ignition wire. I have energized the pink/white and pink/green ignition wires and the blue and the pink / YELLOW accessory wires. What do I need to do to get the compressor to work and the abs light to go out?

Energize the remaining ignition and accesory wires! You said it yourself!commit your way to jehovah and he will act in your behalf. psalms 37:5

I can't seem to find which wire it is that I need. The advice i got from the wiring diagrams only listed the 4 wires that I used

This advice is from Bulldog Security:

On some Full Size Trucks with Climate Control it may be necessary to connect

(3) extra Accessory wires (PINK / YELLOW) and the DARK BLUE Accessory #1 to turn on the A/C Compressor.

12 VOLT CONSTANT                             RED (+)                                IGNITION SWITCH HARNESS 

 STARTER                                               YELLOW (+)                          IGNITION SWITCH HARNESS   STARTER 2                                           N/A    IGNITION 1                                            PINK/WHITE (+)                     IGNITION SWITCH HARNESS  IGNITION 2                                            PINK/LIGHT GREEN (+)       IGNITION SWITCH HARNESS   IGNITION 3  N/A      ACCESSORY /HEATER BLOWER 1   DARK BLUE (+)                   IGNITION SWITCH HARNESS   

Soldering is fun!

kreg357 wrote: This advice is from Bulldog Security: On some Full Size Trucks with Climate Control it may be necessary to connect (3) extra Accessory wires (PINK / YELLOW) and the DARK BLUE Accessory #1 to turn on the A/C Compressor. 12 VOLT CONSTANT              RED (+) IGNITION SWITCH HARNESS   STARTER                 YELLOW (+)                          IGNITION SWITCH HARNESS   STARTER 2             N/A    IGNITION 1              PINK/WHITE (+)      IGNITION SWITCH HARNESS  IGNITION 2              PINK/LIGHT GREEN (+)       IGNITION SWITCH HARNESS   IGNITION 3  N/A       ACCESSORY /HEATER BLOWER 1   DARK BLUE (+)    IGNITION SWITCH HARNESS

That seems like the same wires I have already connected. You mention there are three accessory wires but i think those are what I currently have energized. What color is accessory number 3?

Ok there were 3 pink / YELLOW, 2 smaller and one larger wires. I was already using one of the smaller ones and when I energized the other small pink / YELLOW ABS light went out and the a/c compressor worked, WooHoo! Sheesh, I am glad to be done with this install, although I didn't diode isolate some things so maybe I will have to fix it later. Thanks

Sorry to bump this thread. But just had a question. My remote start only has one Acc (+) output, so i could use this for the Blue accessory wire. I have a wire that is 200mA (-) Second Accessory Output when the remote start has started the vehicle, how would i wire a relay to energize these three pink/white wires. Do the other three wires have to be isolated? Thanks

rjkboyle wrote: Sorry to bump this thread. But just had a question. My remote start only has one Acc (+) output, so i could use this for the Blue accessory wire. I have a wire that is 200mA (-) Second Accessory Output when the remote start has started the vehicle, how would i wire a relay to energize these three pink/white wires. Do the other three wires have to be isolated? Thanks

85- neg second accessory output 86+87- 12 volts 30- your accessory wire you still need energized.A DMM is a beautiful thing.

MECP Advanced Installer Certified.

Ok thanks. If there multiple wires for the sec acc but they are the same color can they be connected to the relay together or do I need to do each individually