07 toyota camry

Home / the12volt's Install Bay / Car Security and Convenience / 07 toyota camry (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

pitoaudiovisual

Copper - Posts: 388

Joined: April 25, 2005

Location: Pennsylvania, United States

Posted: October 04, 2010 at 10:09 AM / IP Logged

I did an install for an 07 Toyota Camry with a crimestopper 500 and the car remote starts for a few then turns off. Its not a bypass issue the bypass is working fine but also on the dash there is a VSA and ABS light on. Also when the alarm arms and disarms no flashing lights but when the car remote starts the lights turn on.

Confidence is the key to any project!!

Search for other posts by pitoaudiovisual

icearrow6

Copper - Posts: 497

Joined: February 02, 2009

Location: California, United States

Posted: October 04, 2010 at 12:17 PM / IP Logged

When the vehicle stops after you remote start. Does it try to restart again?

If if does then I would check the TACH wire to make sure is secure and a DMM to verify that you are getting a reading.

pitoaudiovisual

Copper - Posts: 388

Joined: April 25, 2005

Location: Pennsylvania, United States

Posted: October 04, 2010 at 1:28 PM / IP Logged

yes it does i thought i programmed the car to work off of voltage but i will try to connect the Tach and see what happens. Do u have any idea why the VSA and ABS light would go on as its remote starting tho.

Confidence is the key to any project!!

kreg357

Platinum - Posts: 7,783

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: October 04, 2010 at 5:50 PM / IP Logged

Did you connect the remote starters' outputs to both Starter wires and both Ignition wires at the ignition switch harness?

Soldering is fun!

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: October 04, 2010 at 5:50 PM / IP Logged

Did you connect both ignition wires?

Tach is an easy connection, black right at the OBD connector...

Mike M2

Tech Manager

CS Dealer Services

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: October 04, 2010 at 5:53 PM / IP Logged

that usually indicated a required IGN or ACC is not being powered up.....

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

pitoaudiovisual

Copper - Posts: 388

Joined: April 25, 2005

Location: Pennsylvania, United States

Posted: October 04, 2010 at 8:43 PM / IP Logged

ok i connected both ignitions and starters but now what happens is the car starts fine some times but then other times the car wants to start and the LCD remote says the car is on and the lights inside the car are on as well as the parking lights but the vehicle is not on. I put the remote starter to work by voltage not by tach could that be the reason but y sometimes yes and sometimes no.

Confidence is the key to any project!!

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: October 04, 2010 at 8:58 PM / IP Logged

Try it and find out. Again, a very easy connection...

Mike M2

Tech Manager

CS Dealer Services

kreg357

Platinum - Posts: 7,783

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: October 04, 2010 at 8:59 PM / IP Logged

Switch to Tach mode and use the Tach signal, Black wire at Pin 9 of the OBD 2 connector, as Mike suggested.

Soldering is fun!

sotujr

Member - Posts: 1

Joined: October 04, 2010

Location: Texas, United States

Posted: October 04, 2010 at 11:59 PM / IP Logged

As for the parking lights not flashing during lock/unlock....make sure the light switch is turned off and not on "auto".

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.