2001 silverado, ultrastart 1272

I have installed an Ultrastart 1272 on my 2001 Silverado. Everything seems to be working except when starting the engine continues to crank. originally hooked it up tachless, then added tach wire to one of the fuel injectors. It Tach learned in both setups. I have started the remote start, then turned the key to on, to see if it was something with the Passlock II, same outcome continues to crank. The only wire I am not sure about is the Blue wire in the 9 pin connector the description is Neg Trigger to Start / Glow Plug - Programmable. Default is Gas Mode. I do not have this wire hooked up to anything. My engine is Gas. This has me stumped, any help would be greatly appreciated.

When you switched from Tachless to Tach mode, did you perform the Factory reset?  Try the Factory reset, make sure you have a good Tach wire connected to the 1272s' Blue/Black tach wire and just start the truck ( with a warm engine ) with the key.  It shouild give the Tach Learn confirmation.Soldering is fun!

Yes I have performed the factory reset several times. I have even tried the manual tack learn while in reverse for lower rmp. It would not sense the Tach in manual tack learn, but learned tachless for what ever reason. So performed the factory reset and tach learned in auto. It picks up the Tach everytime. There is not a Blue/Black wire on this model, the Tach wire from the manual is Blue/White.

What type of bypass?  Can you get it to Pit Stop ( or Idle mode )?  Both Ignition wires getting power?Soldering is fun!

Bypass is Ultrastart Tr-2 Universal Remote Starter Key Transponder. it will pit stop fine. it will not start correctly by turning the Key to on and then remote starting though. Both ignition wires are getting power.

Is the Ultrastart Tr-2 Universal Remote Starter Key Transponder a bypass module that will do Passlock2?  There is no chip in the key, it is resistive based in the ignition cylinder itself. Soldering is fun!

Even if the TR-2 Bypass is the issue, it should have worked correctly when I had the key turned to the on position and used the remote start.

True, unless there are two issues with the install.  No prior problems with the Passlock2?  It always starts OK with the key?Soldering is fun!

No issues past or present with Passlock system.  Starts fine with the key. 

Here are my notes from one I did a while ago.

 U1272           Signal                        2001 Silverado

YELLOW        Starter                 Yellow (thin)    @Ignition HarnessRED                Power                  Red                 @Ignition HarnessGREEN          Accessory            Orange           @Ignition HarnessBLUE             Ignition                  Pink                @Ignition HarnessWHITE           Ignition2               White  (thin)    @Ignition Harness        U1272 Default settingRED                Power                  RED / White        @Ignition Harness

Accessory2  extra 30/40A SPDT + 20A fuse     U1272 Program Menu 1, Setting 5, Option 1  for Relay control

Relay Pin 85 to U1272 Black AUX1

Relay Pin 86 and 87 to Red +12v @ Ignition Harness thru 20A fuseRelay Pin 30 to Brown   @ Ignition Harness   ACC2Relay Pin 87a not used

White    (+)Parking Lights                 Brown        @BCM Light Blue Plug

Black    Chassis Ground

Green    (-)Lock   Relay conversion to (+)       Light Blue    @BCM Brown Plug

Blue       (-)Unlock Relay conversion to (+)     White            @BCM Brown Plug

WHITE/ Blue     (-)Horn                  Black            @ BCM Brown Plug

Pink                (+)Brake                White            @ Brake PedalBlue/White     (AC)Tach              Fuel Inj         @ any F.I. -  not Pink

Brown            (-) Disarm             Light Green   @ BCM Violet Plug

Passlock2  -  DEI 556LW

Code = Yellow               @ Ignition Ref = ORANGE / Black      @ Ignition

Soldering is fun!