2006 focus python 1401

I am very familiar with electronics in general. never have done a install for a remote start though. want to make sure i am on the correct note.... please help guys. im going to mark ones that i think i do not need to hookup with a *NOT USED* and ones i am not sure about with *?????* tell me if im right. Thankyou! Main Harness (H1), 12-pin connector H1/1 RED / WHITE (-) 200mA AUX/TRUNK RELEASE OUTPUT    H1/2 RED (+)12VDC CONSTANT INPUT H1/3 BROWN (-) 200mA HORN HONK OUTPUT H1/4 WHITE/ BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay H1/5 BLACK (-) CHASSIS GROUND H1/6 VIOLET (+) DOOR TRIGGER INPUT H1/7 BLUE* FACTORY HORN INPUT (Use jumper to set polarity)     *?????* H1/8 GREEN (-) DOOR TRIGGER INPUT (N/C** OR N/O) H1/9 BLACK/ WHITE (-) 200mA DOME LIGHT SUPERVISION OUTPUT   *NOT USED* H1/10 WHITE/ BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT    *?????* H1/11 WHITE PARKING LIGHT OUTPUT H1/12 ORANGE (-) 500mA GROUND WHEN LOCKED OUTPUT   *NOT USED* H2 Harness, 18-pin connector H2/1 LIGHT GREEN/ BLACK (-) 200mA OEM ALARM DISARM OUTPUT    *?????* H2/2 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT   *NOT USED* H2/3 GREEN / WHITE (-) 200mA OEM ALARM ARM OUTPUT    *NOT USED* H2/4 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT   *NOT USED* H2/5 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT    *NOT USED* H2/6 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT    *NOT USED* H2/7 GREY/BLACK (-) DIESEL WAIT TO START INPUT    *NOT USED* H2/8 N/A    *NOT USED* H2/9 VIOLET/WHITE TACHOMETER INPUT H2/10 DARK BLUE (-) 200mA STATUS OUTPUT    *?????* H2/11 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT    *NOT USED* H2/12 ORANGE (-) 200mA ACCESSORY OUTPUT   *NOT USED* H2/13 PURPLE (-) 200mA STARTER OUTPUT *NOT USED* H2/14 PINK (-) 200mA IGNITION 1 OUTPUT   *NOT USED* H2/15 GREY (-) HOOD PIN INPUT (N/C OR N/O) H2/16 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT   *NOT USED* H2/17 BROWN (+) BRAKE SHUTDOWN INPUT H2/18 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT Remote Start, (H3) 8-pin connector H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT H3/2 RED / WHITE +12V FUSED (30A) IGNITION 2/FLEX RELAY INPUT   *?????* H3/3 ORANGE (+) ACCESSORY OUTPUT *NOT USED* H3/4 VIOLET (+) STARTER OUTPUT H3/5 RED +12V FUSED (30A) IGNITION 1 INPUT H3/6 PINK/WHITE IGNITION 2/FLEX RELAY OUTPUT   *NOT USED* H3/7 PINK/BLACK FLEX RELAY INPUT 87a (IF REQUIRED) OF FLEX RELAY   *?????* H3/8 RED / BLACK +12V FUSED (30A) ACCESSORY/STARTER INPUT   *?????* i just need a better idea of what NEEDS to be hooked up and what does not. Also what else do i need? i have a relay and harness but do i need anything for factory security system? im using this for the wires.... http://www.directwholesale.net/diagrams/printpage.asp?ModelID=14085&MakeID=18 if someone would like to copy and paste the part on each wire and tell me which ones NOT to hookup i would greatly appreciate it! :)

H/1 4 N/A H/1 6 N/A H1/ 7 Do you have a factory alarm? H1/ 10 NA H2/ 1 and 3, again is there a factory alarm? H2/ 10 Will be used to trigger whatever by-pass you need. H3/ 2, 6, and 7 N/A H/3 8 Connect. PM me with your email address, I'll send you the DEI list for this vehicle.

thankyou! i pm'ed you! which bypass module do i need now?

what is a good bypass that is not super expensive..? installing python 1401 if it is without another key id prefer that thanks guys

DEI 1100F can be had online really cheap and has been proven extremely reliable. You need two valid keys to program it but do not have to lose a key to use it.Installer, IT support, and FFL. I need less hobbies.

any others you recommend?

The 1100F is probably the cheapest you will find. However there are a ton of options. My preference in bypass modules are those made by Idata. In actuality although the 1100F is labeled as DEI, I believe it was made by Idata and labeled as DEI. Here is what Idata offers for your 06 Fusion: linkInstaller, IT support, and FFL. I need less hobbies.

Thanks Twelvoltz, I was a bit lost here, in the UK we've had 3 body changes and 3 wiring part colour changes since 98, thank goodness this year's new model will be the same on both sides of the pond.

Bought the ADS-TB at local dealer, 47 and some cents and they programmed it for me :) now i just need to get the girlfriend over to get it installed :) thanks i may have more questions

confused on the heavy geauge wires on which ones to hookup.... Remote Start, (H3) 8-pin connector H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT Confused on where this one goes and other ignition (h5) H3/2 RED / WHITE +12V FUSED (30A) IGNITION 2/FLEX RELAY INPUT   *NOT USED* H3/3 ORANGE (+) ACCESSORY OUTPUT *NOT USED* H3/4 VIOLET (+) STARTER OUTPUT   GOOD H3/5 RED +12V FUSED (30A) IGNITION 1 INPUT    where does this go H3/6 PINK/WHITE IGNITION 2/FLEX RELAY OUTPUT   *NOT USED* H3/7 PINK/BLACK FLEX RELAY INPUT 87a (IF REQUIRED) OF FLEX RELAY   *NOT USED* H3/8 RED / BLACK +12V FUSED (30A) ACCESSORY/STARTER INPUT   where does this go?