remote start and check engine light

I recently installed a bulldog deluxe 500 remote start in my 2004 dodge ram diesel. Everything starts and functions great. I get a check engine light that when checked shows now code. I can clear the light and it will not come on again until i use the remote start to start the truck. Another issue that might be related or maybe not, is that when the truck is running with the remote start the brake warning light on the cluster is lit, even though the parking brake is not engaged, as soon as you put the key in the ignition and hit the brake to disable the remote start the brake warning light goes off. Has anyone had a similar experience with an install?

I meant that when it is checked it shows no code, in reference to the check engine light. Almost the truck is an auto trans.

 IGNITION 1      PINK/WHITE (+)      IGNITION SWITCH HARNESS        IGNITION 2      PINK/LIGHT GREEN (+)      IGNITION SWITCH HARNESS        IGNITION 3      N/A              ACCESSORY /HEATER BLOWER 1      DARK BLUE (+) See NOTE *8      IGNITION SWITCH HARNESS       NOTE *8 On some Full Size Trucks with Climate Control it may be necessary to connect (3) extra Accessory wires (PINK / YELLOW) and the DARK BLUE Accessory #1 to turn on the A/C Compressor      Battery          RED          (+)          IGNITION SWITCH HARNESS                Ignition 1          PINK/WHITE          (+)          IGNITION SWITCH HARNESS                Ignition 2          PINK/GREEN          (+)          IGNITION SWITCH HARNESS                Ignition 3          PINK/LIGHT GREEN          (+)          IGNITION SWITCH HARNESS                Accessory 1          THICK BLUE          (+)          IGNITION SWITCH HARNESS                Accessory 2          PINK / YELLOW          (+)          IGNITION SWITCH HARNESS           Sounds like you missed an ing or acc wire code and bulldog lists are above you will need to test to find outIf i Can't Install it    I Don't need it   Joe

Agree with chev104275.

Here is wiring info from Audiovox:

 Battery                RED  (+)                                   IGNITION SWITCH HARNESS  

 Ignition 1             PINK/WHITE  (+)                   IGNITION SWITCH HARNESS  

 Ignition 2             PINK/GREEN  (+)                 IGNITION SWITCH HARNESS  

 Ignition 3             PINK/LIGHT GREEN  (+)    IGNITION SWITCH HARNESS  

 Accessory 1       THICK BLUE  (+)                   IGNITION SWITCH HARNESS   **See Note

 Accessory 2       PINK / YELLOW  (+)                IGNITION SWITCH HARNESS  

 Starter 1              YELLOW  (+)                          IGNITION SWITCH HARNESS

Note: THIS WIRE MUST BE ENERGIZED DURRING REMOTE START TO PREVENT THE ABS LIGHT FROM COMMING ON

It differs from Bulldogs' info.  I would check the ignition harness with a DMM for the extra wires listed and power any extra wires found to see if it clears the problem.

Soldering is fun!

I see that you both listed a pink lt/green wire as a thrid ignition wire, but I cannot find this and did not have this wire listed on any of the other diagrams that I have found. I have everything else listed though, and they are all hooked up correctly?

I also had to use relays to get power to 2 other accessory wires that supplied power to the AC, which I though was why I was getting the cel, but I have supplied power to these, through relays and am still get the cel.

Judging by this statement and something I read in an older power while researching this, I think that this could be related, because my brake warning light is on as well. I am unable to find anything in the manual or programing on a way to change this or it it actually does or does not provide power during cranking. ANY IDEAS? I am about to just piggy back this off of one of the ignition wires with a relay to see if it solves the problem but I hate to tear back into the wiring and have to go buy another relay just to see. I already have 5 relays tucked up under there for this system so far.

damora wrote: I tried to quote this in the last post but it did not work. Here is the statement I was reffereing to Note: THIS WIRE MUST BE ENERGIZED DURRING REMOTE START TO PREVENT THE ABS LIGHT FROM COMMING ON

OK, I ran a relay to the blue wire and triggered it with the ign 1 wire from the remote start, this got rid of the brake warning and ABS light but I am still getting the check engine light. I have check the wiring harness over several times and can find no wires that I left out and everytime I check for codes there are none store, I can tell it to erase and it will turn the light off, but as soon as I use the remote start, the check engine light comes back on

I checked the diagram and cannot find a 3rd ignition wire that is pink/grn ( I said lt/green in my earlier post but what I was calling grn they are calling light green )

Well I cleared the check engine light and tried it again with the relay giving power to the BLUE wire from the ignition switch at all time (including during cranking) and it seemed to have taken care of the CEL. I will keep an eye on it, but I tried a few more times and it seems to be staying off now. Hopefully that was the solution.