viper 5091 lc3 on 2002 civic coupe ex

So far i got most of the alarm part done, but kind of lost on the remote start part. H1/1 RED / WHITE AUX/TRUNK OUTPUT @@ n/a H1/2 RED 12VDC CONSTANT INPUT @@ gray backup battery H1/3 BROWN SIREN OUTPUT @@ red siren H1/4 WHITE/ BROWN PARKING LIGHT ISOLATION WIRE @@ ?? H1/5 BLACK GROUND @@ ground H1/6 VIOLET + DOOR TRIGGER @@ notused H1/7 BLUE TRUNK PIN/INSTANT TRIGGER INPUT @@ red(alarm) H1/8 GREEN - DOOR TRIGGER @@ GREEN/ red(alarm) H1/9 BLACK/ WHITE DOME LIGHT SUPERVISION OUTPUT @@ ?? H1/10 WHITE/ BLUE REMOTE START/ TURBO TIMER ACTIVATION INPUT @@ not used H1/11 WHITE PARKING LIGHT OUTPUT @@ blue(alarm) H1/12 ORANGE GROUND WHEN ARMED OUTPUT @@ n/a H2/1 LIGHT GREEN/ BLACK OEM ALARM DISARM OUTPUT @@ ?? H2/2 ORANGE / BLACK AUX 4 OUTPUT @@ notused H2/3 GREEN / WHITE OEM ALARM ARM OUTPUT @@ ?? H2/4 VIOLET/BLACK AUX 2 OUTPUT @@ notused H2/5 WHITE/ BLACK AUX 3 OUTPUT @@ notused H2/6 WHITE/ VIOLET AUX 1 OUTPUT @@ notused H2/7 GREY/BLACK DISEL WAIT TO STAT INPUT @@ notused H2/8 BROWN / BLACK HORN HONK OUTPUT @@ ?? H2/9 VIOLET/WHITE TACHOMETER INPUT @@ blue(by battery) H2/10 DARK BLUE STATUS OUTPUT @@ bypass module H2/11 PINK/WHITE FLEX RELAY CONTROL OUTPUT @@ ?? H2/12 ORANGE ACCESSORY OUTPUT @@ notused H2/13 PURPLE STARTER OUTPUT @@ notused H2/14 PINK IGNITION 1 OUTPUT @@ notused H2/15 GREY HOOD PIN INPUT @@ hoodpin H2/16 BLUE/WHITE 2ND STATUS/REAR DEFOGGER OUTPUT @@ ?? H2/17 BROWN BRAKE SHUTDOWN INPUT @@ ?? H2/18 BLACK/ WHITE NEUTRAL SAFTEY INPUT @@ ?? H3/1 PINK IGNITION 1 @@ BLACK / YELLOW(ignition) H3/2 RED / WHITE FLEX RELAY INPUT 87 @@ ?? H3/3 ORANGE ACCESSORY OUTPUT @@ BLACK/ red(ignition) H3/4 VIOLET STARTER OUTPUT @@ BLACK/ white(ignition) H3/5 GREEN STARTER INPUT @@ BLACK/ white (keyside) H3/6 RED INGIITON 1 INPUT @@ white H3/7 PINK/WHITE FLEX RELAY OUTPUT 30 @@ ?? H3/8 PINK/BLACK FLEX RELAY INPUT 87A @@ ?? H3/9 RED / BLACK ACCESSORY/STARTER RELAY INPUT @@ white(igniton) Door Lock 1 BLUE UNLOCK OUTPUT @@ WHITE/ green(driver kick) 3 GREEN LOCK OUTPUT @@ WHITE/ blue(driver kick)

H3/2, H3/6, H3/9 to White (+)  12 Volts Constant....H3/7 to WHITE/ Red as Accessory 2, This comes defaulted as Ignition 2 and needs to be changed to Accessory, Menu 3, Item 8, Option 2. All your other H3 wires look OK.

H2/17 to WHITE/ Black (+) above at switch above barke pedal.

http://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp

As always, check and verify all wires with a DMM

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

What about H3/8?

H3/8 should not be needed on your car.When all else fails, Read the Instructions

Support the12volt.com Make a Donation

alright thanks, so far so good, got remote start to work with key in off position. How do i do tach learning or do i not need to do it?

You can download the install manual for the 5901 on this site from the downloads section.  On page 30 explains the tach learning procedure.When all else fails, Read the Instructions

Support the12volt.com Make a Donation

okay got that got the 555i installed, but for some reason its not starting and none of my keys are turning on the car anymore..

nvm the key works now but still wouldn't remote start. The remote start worked when before installing the bypass module tho

Do you get any parking light flashes when tring to remote start?When all else fails, Read the Instructions

Support the12volt.com Make a Donation

No there was no parking light flashes, just gives me an error on my remote