wiring on 2008 ford econoline

Home / the12volt's Install Bay / Car Security and Convenience / wiring on 2008 ford econoline (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

rookie01

Member - Posts: 4

Joined: July 23, 2011

Location: New York, United States

Posted: July 23, 2011 at 8:22 PM / IP Logged

hello i am going to install a viper 5902 on a 2008 ford econoline, i am bit confused with the remote start harness wires, i am used to the older harness with all the relays and little better installation guide. can some one please tell me where to connect the wires for this harness.

thanks for any help or suggestions.

smokeman1

Platinum - Posts: 1,588

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: July 23, 2011 at 9:59 PM / IP Logged

Rather easy install. I did one on my work van E150. Web site below for wiring guide.

H3/2 RED / White, & H3/6 Red & H3/9 RED / Black to 12 Volts constant, H3/1 Pink to Ignition 1, H3/3 Orange to Accessory 1, H3/7 Pink/White to Accessory 2, H3/4 to starter side of cut starter wire, H3/5 to starter side of cut starter wire. Or just H3/5 to starter wire, (uncut).

http://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

rookie01

Member - Posts: 4

Joined: July 23, 2011

Location: New York, United States

Posted: July 24, 2011 at 5:59 PM / IP Logged

smokeman1 wrote:

Rather easy install. I did one on my work van E150. Web site below for wiring guide.

http://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp

thank you much i got the remote start working fine.

but my parking lights when arming the system doesn't flash. i connect the white wire from the alarm to the brown wire in the vehicle. is there another wire need to be connected with these new alarms. can anyone be of assistance.thanks

smokeman1

Platinum - Posts: 1,588

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: July 24, 2011 at 7:02 PM / IP Logged

My first guess would be, did you install the 10amp mini fuse that is located under the cover of the brain? It looks like a door in the middle of the brain, slides up. make sure to check the polarity before inserting.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

rookie01

Member - Posts: 4

Joined: July 23, 2011

Location: New York, United States

Posted: July 25, 2011 at 8:24 PM / IP Logged

smokeman1 wrote:

thanks yep got it to work. do you know the default number of times to press the valet switch to put the alarm in valet mode. and how do i change it. thanks again

smokeman1

Platinum - Posts: 1,588

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: July 25, 2011 at 8:46 PM / IP Logged

Press the "F" button twice, the press the unlock button. Blue light on the antenna should stay on solid in valet mode. Press "F" button twice, press the unlock button to take it out of valet mode. Blue light on antenna should go out.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

rookie01

Member - Posts: 4

Joined: July 23, 2011

Location: New York, United States

Posted: July 25, 2011 at 9:09 PM / IP Logged

smokeman1 wrote:

thanks i know about that way i was wondering what if i dont have the remote and want to do it by the valet on the control center.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

wiring on 2008 ford econoline

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.