the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

programming second remote for bullydog ke

Home / the12volt's Install Bay / Car Security and Convenience / programming second remote for bullydog ke (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 03, 2012 at 12:20 PM / IP Logged  

I am having problems programming the second remote for a bully dog KE1702 I followed the instructions in guide but I can not get it to work.

any help would be great.

 Ralph

kreg357 
Platinum - Posts: 7,787
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: November 03, 2012 at 2:46 PM / IP Logged  
Sometimes it's easier to un-plug the control unit, wait a few minutes , plug it back in and start fresh.
Soldering is fun!
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 03, 2012 at 3:32 PM / IP Logged  
i have try that several times it and still know luck
kreg357 
Platinum - Posts: 7,787
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: November 03, 2012 at 3:51 PM / IP Logged  

It is only allowing you to have one remote on the system?

Have you tried the second remote first after a reset?  ( Just to make sure it works OK. )

Soldering is fun!
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 03, 2012 at 5:20 PM / IP Logged  

yes also try that i must be doing something wrong when i try to prorgam remote.

kreg357 
Platinum - Posts: 7,787
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: November 03, 2012 at 5:43 PM / IP Logged  

Well, if either remote will work by itself and you can't add a second...

It's either a procedural problem or a bad brain.  The programming is pretty basic.  Just press and hold the LOCK button on the working remote for 10 seconds, then

press and hold the LOCK button on the second remote for 5 seconds.  Not sure if there is a time restriction / limit.

Bulldog Security has a good Tech Support group.  Might try them on Monday.  1-800-878-8007

Soldering is fun!
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 03, 2012 at 8:27 PM / IP Logged  
so i do not  have to put it in program mode ?
kreg357 
Platinum - Posts: 7,787
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: November 03, 2012 at 9:46 PM / IP Logged  
Don't think so, but I'm not positive.  Haven't installed a Bulldog unit in many years.  I remember doing a few RS1100's and as soon as they had power applied ( or a memory clear ) you just pressed the LOCK button on each of the remotes and that was it.  Have you tried it without going into Program Mode first?
Soldering is fun!
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 04, 2012 at 5:40 AM / IP Logged  
i will try that that this morning that is probaly what i am doing wrong. i will let you know
hodder 
Member - Posts: 6
Member spacespace
Joined: September 29, 2012
Location: Maine, United States
Posted: November 04, 2012 at 7:02 AM / IP Logged  

yeh got the remote number to to work it was a matter of timing in the program button

      thanks for help


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, May 17, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer