2011 camaro alarm

Home / the12volt's Install Bay / Car Security and Convenience / 2011 camaro alarm (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 20, 2013 at 5:30 PM / IP Logged

I havent started but i did purchase viper 5704 with dball module i have all needed diagrams and i need help understanding the dball diagram on a few connections

powerslave

Copper - Posts: 126

Joined: April 23, 2002

Location: United States

Posted: December 20, 2013 at 6:03 PM / IP Logged

Ok, but don't tell us what connections you are referring to...

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 20, 2013 at 8:00 PM / IP Logged

yea my bad on the dball diagram harness 14 pins 10,11 & 12 is where my confusion is. 2011 camaro alarm -- posted image.

triniforever

Copper - Posts: 323

Joined: November 12, 2008

Location: New York, United States

Posted: December 20, 2013 at 8:54 PM / IP Logged

I did a 2010 Camaro and it was manual too, but I went with Idatalink and I can tell you to remove that BCM is a real PITA and putting it back in is a nightmare and I believe I went with the 5704 also ,but be patient it will take some doing .

triniforever

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 20, 2013 at 9:34 PM / IP Logged

im thinking about going with that 1 myself so did you need any relays or just followed diagrams to the t?

triniforever

Copper - Posts: 323

Joined: November 12, 2008

Location: New York, United States

Posted: December 21, 2013 at 7:49 AM / IP Logged

No relays needed for that car ,just follow the install diagram and you should be fine. Have you ever installed an alarm/remote start on a car before ?

triniforever

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 21, 2013 at 11:34 AM / IP Logged

No not remote start i did 1 on my 88 monte carlo ..... Damn i miss that car I appreciate the help im just confused on the 3 wire from harness 14 wire 10 ORANGE / Red where i have to cut then do ??

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 21, 2013 at 1:11 PM / IP Logged

I cant edit my last post but i didnt mean to put 3 wire just wire 10 ORANGE / red from harness 14

triniforever

Copper - Posts: 323

Joined: November 12, 2008

Location: New York, United States

Posted: December 21, 2013 at 6:46 PM / IP Logged

For instance on pin #2 that wire has to be cut and the ORANGE / Red wire from the DBALL goes to the cut side away from the BCM and the Yellow/Red wire from the DBALL has to be connected to the plug side of the of the wire from the BCM.

triniforever

itsmars

Member - Posts: 23

Joined: December 19, 2013

Location: California, United States

Posted: December 21, 2013 at 7:44 PM / IP Logged

OOOOh OOOk i got you man thanks big time

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.