Hi, Thank you for your recommendations. I have read a lot of good things about the EV0-ALL. So the winner is the EVO-ALL flashed with Hardware 4 and Firmware 4.09 per the installation guide. Also the THAR-CHR4 T-HARNESS.
The following is how we are planning to proceed with the install. We would really appreciate If any of you guys could see if we are on the right path. thank you... IF ANY ERRORS PLEASE HELP AND COMMENT.
Viper 5704 2009 Dodge Journey or EVO-ALL
H1/1 RED (+)12VDC CONSTANT INPUT +12V Constant Battery Source
H1/2 BLACK (-) CHASSIS GROUND Solid Chassis Ground
H1/3 BROWN (+) SIREN 0UTPUT Viper Siren
H1/4 WHITE/ BROWN PARKING LIGHT 87A Not Used
H1/5 WHITE PARKING LIGHT OUT set to (+) WHITE/ Purple (+) in Passenger Kick panel
H1/6 ORANGE (-) 500mA G W A 0UTPUT Not Used
H2/1 PINK/WHITE (-) 200mA IGNITION/FLEX RELAY Not Used
H2/2 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT Chassis Ground ( if Auto Trans )
H2/3 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOG Not Used
H2/4 GREEN/ BLACK (-) 200mA OEM ALARM DISARM Not Used
H2/5 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT Not Used
H2/6 GREEN (-) D00R TRIGGER INPUT (N/C 0R N/0) EVO Green Plug A, Pin A4
H2/7 BLACK / YELLOW (-) 200mA DOME LIGHT SUPER Yellow/white (+) using a relay.
H2/8 BROWN / BLACK (-) 200mA HORN HONK OUTPUT Not Used
H2/9 DARK BLUE (-) 200mA STATUS OUTPUT EVO Dark Blue Plug 4, Pin A8
H2/10 PINK (-) 200mA IGNITI0N 1 OUTPUT Not Used
H2/11 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT Not Used
H2/12 VIOLET (+) D00R TRIGGER INPUT Not Used
H2/13 WHITE/ VlOLET (-) 200mA AUX 1 OUTPUT Not Used
H2/14 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT Not Used
H2/15 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT Not Used
H2/16 BROWN (+) BRAKE SHUTD0WN INPUT EVO Black Plug A, Pin A11
H2/17 GREY (-) H00D PIN INPUT (N/C 0R N/0) EVO Pink/Black Plug A, Pin A15
H2/18 VIOLET / YELLOW (-) 200mA STARTER OUTPUT Not Used
H2/19 BLUE (-) TRUNK PIN / INSTANT TRIGGER INPUT (N/O) Not Used
H2/20 GREY/BLACK (-) DIESEL WAIT T0 START INPUT Not Used
H2/21 WHITE'/BLUE (-) REMOTE START/ TURBO TIMER INPUT Not Used
H2/22 ORANGE (-) 200mA ACCESSORY OUTPUT Not Used
H2/23 VIOLET/WHITE TACHOMETER INPUT EVO Pink Plug A, Pin A12
H2/24 GREEN / WHITE (-) 200mA OEM ALARM ARM OUTPUT Not Used
H3 heavy wires
1 PINK (+) IGNITION 1 INPUT/OUTPUT To EVO Yellow Plug A, Pin A1 and Yellow Wire THAR-CHR4
2 RED / WHITE (30A) FUSED IGNITION 2 Not Used
3 ORANGE ACCESSORY OUTPUT Not Used
4 VIOLET (+) STARTER OUTPUT (CAR SIDE) EVO RED / Blue Plug A, Pin A9
5 GREEN (+) STARTER INPUT (KEY SIDE) Not Used
6 RED (+) FUSED (30A) IGNITION 1 INPUT +12V Constant Battery Source
7 PINK/WHITE (+) IGNITION 2 / FLEX RELAY Not Used
8 PINK/BLACK FLEX RELAY INPUT 87A Not Used
9 RED / BLACK FUSED (30A) ACC/STARTER INPUT +12V Constant Battery Source
Door Lock
1 Blue (-) 500 mA Unlock EVO PURPLE / White Plug A, Pin A3
2 Green (-) 500mA Lock EVO Purple Plug A, Pin A2
EVO-ALL wiring
using the THAR-CHR4 harness
THAR-CHR4 Data-Link 4 Pin Conn. installa guide shows that it supplys the 12v and ground to remote start.
since using 12v constant from battery source. Is this connection still required?
THAR-CHR4 5-PIN CONN. connected to EVO as show on intall guide.
THAR-CHR4 6-PIN CONN. connected as shown on install guide.
IF ANY ERRORS, CORRECTIONS WOULD REALLY BE APPRECIATED IT....
THANK YOU GUYS AND HAVE A WONDERFUL DAY....
Aurelio Zamora