I'm trying to hook up an alarm/remote start system to my cb7. I've got everything down working right except the remote start and I need some assistance. Heres how I have everything wired up... Manual transmission
Main Harness (H1)
H1/1 Red - (+)12vDC constant input (white ignition wire)
h1/2 black - (-) chassis ground (grounded)
h1/3 brown - (+) siren output (red siren wire)
h1/4 WHITE/ brown - parking light isolation wire (not used)
h1/5 white - parking light output (connect and works)
H2 Harness, 24-pin
h2/1 pink/white - (-) 200ma igntion/flex relay control output (do i need this connected? where?)
h2/2 BLACK/ white - (-) neutral safety input (grounded)
h2/3 blue/white - (-) 200ma 2nd status/rear defogger output
h2/4 GREEN/ black - (-) oem alarm disarm output
h2/5 RED / white - (-) 200ma trunk release output
h2/6 green - (-) door trigger input (connected and works)
h2/7 BLACK / YELLOW - (-) 200ma dome light supervision output
h2/8 bronw/black - (-) 200ma horn honk output
h2/9 dark blue - (-) 200ma status output (do i need this connected? where?)
h2/10 pink - (-) 200ma ignition 1 output (do i need this connected? where?)
h2/11 WHITE/ black - (-) 200ma aux 3 output
h2/12 violet - (+) door trigger input
h2/13 WHITE/ violet - (-) 200ma aux 1 output
h2/14 violet/black - (-) 200 ma aux 2 output
h2/15 ORANGE / black - (-) 200ma aux 4 outut
h2/16 brown - (+) brake shutdown input (connected at light green wire at brake switch)
h2/17 grey - (-) hood pin input
h2/18 violet / YELLOW - (-) 200ma starter output (do i need this connected and where?)
h2/19 blue - (-) trunk pink/instant trigger input
h2/20 grey/black - (-) diesel wait to start output
h2/21 WHITE/ blue - (-) remote start/turbo timer activation input
h2/22 orange - (-) 200ma accessory output (do i need this connected and where?)
h2/23 violet/white - tachometer input (read that this wire is not necessary?)
h2/24 GREEN / WHITE - (-) 200ma oem alarm arm output
Remote Start H3
h3/1 pink - (+) ignition 1 input/output (BLACK / YELLOW ignition is this correct)
h3/2 RED / white - (87) flex relay +12v input (white igntion is this correct)
h3/3 orange - (+) accessory output (WHITE/ black igntion is this correct)
h3/4 violet - (+) starter output (car side of starter kill) (BLACK/ white ignition car side)
h3/5 green - (+) starter input (key side of the starter kill) (BLACK/ white ignition key side)
h3/6 red - ignition 1 +12v input (white ignition)
h3/7 pink/white - (30) flex relay output (car side of ign, acc or starter wire) (yellow ignition wire)
h3/8 pink/black - (87a) flex relay input (key side of ign, acc or starter wire if needed) (not using do i need this)
h3/9 RED / black - accessory/starter relay +12v input (WHITE/ black ignition)
h3/10 - no connection
Okay guys this is how I have it hooked up. This is obviously my first time doing this and need assistance with the remote start. When I have it hooked up like this I can't even start my car with the key or remote start. What am I doing wrong? When I try remote start my [arking lights flash 7 times but doesn't start and the key won't even start it.