'95 Sentra GXE Keyless Entry

Home / the12volt's Install Bay / Car Security and Convenience / '95 Sentra GXE Keyless Entry (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

southpaw

Member - Posts: 13

Joined: February 08, 2004

Posted: April 19, 2004 at 8:59 PM / IP Logged

Hey All,

A lot of good info here. All I am trying to do is install a Keyless Entry in my wofes '95 Sentra GXE.

Here is what I got:

http://www.jcwhitney.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10101&storeId=10101&langId=-1&productid=190853&mediaCode=ZX&appId=426669

Just a little cheapie system.

I am very comfortable with electronics, but I just can't get the symantecs of "where" this gets installed?

Is it under the hood?? In the door?? Where does the actual "box" go and where do the connections get made??

thx and sorry for the newbie posts

Southpaw

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: April 19, 2004 at 9:13 PM / IP Logged

Make: Nissan

Model: Sentra

Year: 1995

Alarm

Constant 12 volts GREEN IGNITION SWITCH HARNESS

Ignition 12 volts BLACK/ RED IGNITION SWITCH HARNESS

Starter BLACK/ WHT (AUTO TRANS) BLACK / YELLOW (MAN.TRANS) IGN SW HARN

Dome Light RED / WHITE (-) 20 PIN CONN.IN DRIVER KICK PANEL

Trunk Pin Switch RED (-) @ TRUNK SWITCH,LAMP OR OEM THEFT UNIT

Parking Lamp RED / BLUE (+) HEADLIGHT SWITCH OR FUSE/JUNCTION BOX

Power Lock GRAY AT WHITE 16 PIN CONNECTOR #201

Power Unlock PURPLE IN DRIVER KICK PANEL

#201- See Negative Pulse Door Lock Diagram.

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

southpaw

Member - Posts: 13

Joined: February 08, 2004

Posted: April 20, 2004 at 8:09 AM / IP Logged

ok......when I said I was a newbie at this...I really meant it.. ;-)

Here is the info I have gleened so far:

My Sentra has Negative Pulse Door Locks

Power Lock(Gray) & Power Unlock(Purple) both in the Driver Kick panel

I still have some questions:

1) I assume I need to apply both a Ground and Constant +12V to the keyless module? Can I get these in the Kick Panel?

2) Would I tap into the wires at the switch itself or in the kick panel?

3) Where would the actual Keyless module reside?? (by the Kick panel or in the door?)

4) Where is the best way to stretch out the antenna wire?

Sorry for all the "very basic" questions, but I have never done this and would like to do it right..

thx

Southpaw

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: April 20, 2004 at 8:49 AM / IP Logged

1. Constant 12 volts GREEN IGNITION SWITCH HARNESS

you can get the ground anywhere..

2.are you talking about the door locks???

if so, you would run the door lock wire from the alarm right to the door lock wire in the car. the wires coming from the alarm must be a neg. output for this to work...

3.put the unit high under the drivers dash..

4.just make sure it is not tounch any metal....i just leave mine rolled up...

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

southpaw

Member - Posts: 13

Joined: February 08, 2004

Posted: April 20, 2004 at 9:29 AM / IP Logged

thx...as for #2...yes..I was talking about the 2 door lock/unlock outputs.

Would I tap into them at the harness in the kick panel, or directly at the Master window switch in the driver door??

opy1095

Member - Posts: 48

Joined: October 04, 2003

Location: United States

Posted: April 20, 2004 at 12:12 PM / IP Logged

im having problems w/ door locks for my 95 Sentra.

do i need relays and exactly where do i connect the lock and unlock wire

opy1095

Member - Posts: 48

Joined: October 04, 2003

Location: United States

Posted: April 20, 2004 at 12:15 PM / IP Logged

Having problem w/ door locks.

Exactly where do i connect the lock and unlock wires

Do i need relays?

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: April 20, 2004 at 4:08 PM / IP Logged

as long as the output from the alarm is a neg output, hook the wire stright to the door lock wire:

Power Lock GRAY AT WHITE 16 PIN CONNECTOR #201

Power Unlock PURPLE IN DRIVER KICK PANEL

#201- See Negative Pulse Door Lock Diagram.

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

southpaw

Member - Posts: 13

Joined: February 08, 2004

Posted: April 20, 2004 at 4:13 PM / IP Logged

thx draasch..

just trying to clarify..I know I splice the negative alarm outputs directly into the door look wires...

I am just wondering if I can hook it all up in the Kick Panel or if I have to snake the alarm output wires into the door and up to the switch itself??

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: April 20, 2004 at 5:18 PM / IP Logged

in the drivers kick panel....just look for the above wires and test with a meter...then you can just tap into them...

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.