clifford smart windows 2

Home / the12volt's Install Bay / Car Security and Convenience / clifford smart windows 2 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

webstar

Member - Posts: 17

Joined: October 03, 2004

Location: United Kingdom

Posted: October 07, 2004 at 10:34 PM / IP Logged

First to say i am very new to this but trying.

when fitting smart windows 2 the diagram states to look for 12v on the window switch when pressing up or down then cut this wire and attach orange wire to motor side and blue to switch side and vice versa passenger switch.

but when i test for 12v on the switch its there already and goes to 0 volts when the switch is pessed.

i know im a bit slow but this is confussing.

Any help

webs

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: October 08, 2004 at 3:37 PM / IP Logged

It would be most helpful to know the vehicle make, model, year, which this device is being installed into.

Regards

EVIL Teken . . .

webstar

Member - Posts: 17

Joined: October 03, 2004

Location: United Kingdom

Posted: October 08, 2004 at 9:16 PM / IP Logged

Hi Teken

The vehicle is a 1996 Fiat coupe turbo 16valve 2.0 and its driving me nuts.

But thanks for all your help so far.

webs

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: October 08, 2004 at 9:58 PM / IP Logged

DIRECTWIRE™ WIRING INFORMATION - FIAT / COUPE (UK) / 1994 / Remote Start

12volts

Starter

Second Starter

Ignition ORANGE / white ignition harness

Second Ignition

Third Ignition

Accessory

Second Accessory

Keysense

Power Lock lt blue - entry point from door to veh

Power Unlock white - entry point from door to veh

Lock Motor

Unlock Motor

Parking Lights+ blue & blu/blk rear of the fusebox

Parking Lights-

Hazards

Turn Signal(L)

Turn Signal(R)

Reverse Light

Door Trigger BLACK/ violet - rear of fusebox, conn G or E

Dome Supervision

Trunk/Hatch Pin BLACK/ violet at the bootlight

Hood Pin

Trunk/Hatch Release

Power Sliding Door

Factory Alarm Arm

Factory Alarm Disarm

Disarm No Unlock

Tachometer

Wait to start

Brake Wire

Parking Brake

Horn Trigger

Memory Seat 1

Memory Seat 2

Memory Seat 3

Immobilizer Bypass Module: Not Available

This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.

The wiring is for a 1994 Fiat Coupe, perhaps this will give you some reference.

Regards

EVIL Teken . . .

Teken

Gold - Posts: 1,492

Joined: August 04, 2002

Location: Aruba

Posted: October 08, 2004 at 10:03 PM / IP Logged

This link will summerize for you the back ground and theory as to how to interface the window module.

Please take a few moments to review the material, and hopefully this will answer your Q's.

Regards

EVIL Teken . . .

http://www.directechs.com/techtips/pdfs/resources/security/directed_techtips/1042.pdf

webstar

Member - Posts: 17

Joined: October 03, 2004

Location: United Kingdom

Posted: October 08, 2004 at 11:32 PM / IP Logged

Many thanks Teken

This lot is spot on .

Many, Many thanks

webs

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

clifford smart windows 2

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.