Installing new Cillford RSX 3.5

Home / the12volt's Install Bay / Car Security and Convenience / Installing new Cillford RSX 3.5 (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

Era1

Member - Posts: 13

Joined: February 07, 2005

Location: United States

Posted: February 11, 2005 at 1:08 AM / IP Logged

I have the 01 Toyota Highlander and want to install the RSX 3.5. I need to know what important thing that I should look for before install the alarm. I already got the wiring diagram for my car. Also I got the 556U transponder. I know the RSX 3.5 come with the 451M relay. Do I need the relay install for the door lock/unlock function. The other post I look at and they said the don't need it. Can anybody tell me how to connect this wire,are thosr wire connect direct to the lock/unlock switch inside the door? What about domelight supervison. Do I need the relay and what wire do I need to connect to? My can only has 1 ignition accessory cable. Can I connect both accessory wire form the alarm into this wire? And the neutral safety switch. Where is the wire in car and what color is this? What kind the options that I can add to this alarm(beside the pop open the door and open the windows)? And for the last QUESTION. For a NEWBIE and never install the alarm before, but have electronic skil and have no problem soldering. How hard is it to do this installation? I check for the labor in the local area and they charge over $350. It cost more that the alarm itself. Also if I don't try it and I will never learn. With all the expert here to help I thing I can do this.

Sorry for the long list but I just don't want to screw up anything.

Thanks for all the reply.

Back to Top

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: February 11, 2005 at 6:59 AM / IP Logged

http://www.directechs.com/techtips/pdfs/resources/security/directed_techtips/1070.pdf

12volts	white & blu/yel	+	ignition harness
Starter	BLACK/ white	+	ignition harness
Second Starter
Ignition	black	+	ignition harness
Second Ignition	BLACK / YELLOW	+	ignition harness
Third Ignition
Accessory	pink	+	ignition harness
Second Accessory
Keysense
Power Lock	see direct fax
Power Unlock	document #1070
Lock Motor	BLACK/ white		17 pin plug, pin 1 @ BECU
Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right.
Unlock Motor	blue/red		17 pin plug, pin 2 @ BECU
Notes: The BECU (Body ECU) is behind the glove box, it is the module to the right.
Parking Lights+	green		driver kick panel
Parking Lights-	GREEN/ red		headlight switch
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	GREEN/ YELLOW	-	ign. key cyl. illumination
Notes: To avoid the dome light delay, go to the Body ECU behind the glove box to get the individual door trigger wires. In the 19 pin plug, the driver door is RED / blue in pin 11 and the rear hatch is WHITE/ red in pin 6. In the 17 pin plug, the front passenger door is RED / blue in pin 16 and the 2 rear door is red in pin 15. Use all wires and diode isolate each.
Dome Supervision	comes on with unlock
Trunk/Hatch Pin	WHITE/ red	-	driver kick panel
Hood Pin	GREEN/ black	-	top plug, pass side junc box
Trunk/Hatch Release
Power Sliding Door
Factory Alarm Arm	arms with lock
Factory Alarm Disarm	disarms with unlock
Disarm No Unlock	red to blue	-	steering column
Notes: This is the key sense wire for the ignition switch. The wire changes colors after a junction plug. It is red on the ignition switch side and blue on the other side. Using the status output wire from the remote start to ground this wire will disarm the alarm without unlocking the doors.
Tachometer	WHITE/ green		28 pin plug, pin 27 @ ECM
Notes: The ECM (Engine Control Module) is behind the glove box, it is the module to the left.
Wait to start
Brake Wire	GREEN / WHITE	+	brake pedal switch
Parking Brake
Horn Trigger	WHITE/ red	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Immobilizer Bypass Module:	Required: Yes	Type: Transponder	Part #: 555X, 556U, or 555U
Notes: N/A

how own your mind, control your life.

MECP certified. always use a DMM

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Installing new Cillford RSX 3.5

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.