95 Chrysler LHS alarm wiring?

Okay My car got stolen so when I got it back I purchesed a Clifford Arrow 5 alarm system. I drive a 95 Chrysler LHS with factory keyless and alarm...how would I override this? Wiring for alarm... Also can someone match up the wiring for me. The only ones I dont understand totally light polarity and outputs(white wire) Instant trigger and (-)acc output A(is this for trunk pop) and output when armed Thanks a ton.... Jay Alarm wiring 1 black- chasis ground 7 blue- (-) instant door trigger 8 violet- (+) door trigger 9 Green- (-) door trigger 10 Red- (+)12v power input 11 Brown- (+) siren output 12 WHITE/ red- Light flash Polarity 13 white- Light flash output 14 white- Light flash output 15 BLACK/ white- (+) dome light output 16 RED / white- (+) acc output 17 Orange- (-) output when armed 18 Yellow- (+) ignition plug in Door lock pin Green Blue Here is the wiring for the car 1995-97 Chrysler LHS Security Information Constant 12V+     Pink/Black       Ignition Switch Harness Starter      Yellow/Gold       Ignition Switch Harness Ignition      Dark Blue       Ignition Switch Harness Ignition 2      RED / White 12GA       Ignition Switch Harness Ignition 3      RED / White 18GA       Ignition Switch Harness (Air Bag Light) Accessory      BLACK/ Orange       Ignition Switch Harness (Heat/AC) Tach      Red       WHITE/ Black (PCM Passenger's Wheel Well 2 Cylinder Setting) Neutral Safety Wire      BLACK/ Light Green       Switch on Driver's Side or Transaxle Brake Switch      White or WHITE/ Tan       Brake Switch Trunk Release      BLACK/ White (+)       Switch in Glove Compartment Trunk Pin      BROWN / Black (-)       Driver's Kick Panel Parking Lights      BLACK / YELLOW       Driver's Kick Panel Head Lamp      Green       Light Switch Hood Pin      n/a        Factory Disarm      Light GREEN/ Orange (-)       High Driver's Kick Panel Door Trigger      Yellow (-)       Driver's Kick Panel White 20 Pin Connector Door Lock      ORANGE / White       Behind Fuse Panel at Door Lock Relays Door Unlock      Pink/Purple       Positive Trigger Horn Wire      BLACK/ Red (-)       Horn Relay in Fuse Panel Dome light supervision       tan(-) Windows Up      LF=Light Blue/Gold, RF=BROWN / White, LR=Blue/White, RR=Gray/Black Windows Down      LF=WHITE/ Gold, RF=PURPLE / White, LR=RED / Black, RR=GREEN / WHITE

Not sure but I think 1995 wires you have are different from mine.....

METER ALL wires..........to be sure

Others may add to this Basic Install..........

TRY:

1 black- chasis ground = Yep

2 not used =x

3 not used =x

4 not used =x

5 not used =x

6 not used =x

7 blue- (-) instant door trigger =  tan & tan/red : driver kick panel :

Tan gets drivers door, tan/red gets pass. doors. Tap both wires and diode isolate.

8 violet- (+) door trigger =x

9 Green- (-) door trigger = tan & tan/red : driver kick panel :

Tan gets drivers door, tan/red gets pass. doors. Tap both wires and diode isolate.10 Red- (+)12v power input =  pink/black or red (20A)

11 Brown- (+) siren output 12 WHITE/ red- Light flash Polarity = pink/black or red (20A)

13 white- Light flash output =  BLACK / YELLOW ::driver kick panel 14 white- Light flash output =  BLACK / YELLOW ::driver kick panel 15 BLACK/ white- (+) dome light output 16 RED / white- (+) acc output =  BLACK/ white 17 Orange- (-) output when armed = Starter Disable Relay

18 Yellow- (+) ignition = dk. blue/gold dots

plug in Door lock pin Green = ORANGE / white + RELAY

Can also pulse Factory Disarm ( if U have ) with Negative = lt.GREEN/ orange 20ga :

either kick Blue = pink/purple + RELAY

MO

Don't Learn from Others Mistakes

You Might Be the One That Knows.

Now for the relays which do I buy and how would that get wired up....and what diode to use.. I am a moron when it comes to alarms but great with audio so i feel like a moron for asking these Q's but thanx alot for the info the wiring looks the same. Jay

You can use 1N4001 diode

3 SPDT Relays:

Relay 1

LOCK:

PIN 87 = ORANGE / white Lock wirePIN 87a = XXPIN 30 = Constant 12 volt ( + ) : pink/black or red (20A)PIN 85 = Negative Lock Output from CliffordPIN 86 = Constant 12 volt ( + )

Relay 2

UNLOCK:

PIN 87 =Pink/purple Unlock wirePIN 87a = XXPIN 30 = Constant 12 volt ( + ) : pink/black or red (20A)PIN 85 = Negative UNLock Output from  CliffordPIN 86 = Constant 12 volt ( + )

Relay 3

DISARM

PIN 87 =lt.GREEN/ orange 20ga PIN 87a = XXPIN 30 = GROUNDPIN 85 = Negative UNLock Output from CliffordPIN 86 = Constant 12 volt ( + )

MO

Don't Learn from Others Mistakes

You Might Be the One That Knows.

Also sorry one more lol should i cut these wires and hook them to the relay or splice them or does it matter??? Thanks and sorry wont bug u anymore...I wish u lived around here I would owe ya a few beers for all this work u did for me....I appreaciate it alot Jay

So in total I will need 4-20 amp fuses.(relay 1, relay 2, power and light flash polarity) 3 relays and 2 diodes. If i dont need the relays do i just hook the alarm wires straight to the power lock and unlock positive?? Thanks Jay

According to Clifford wiring diagram, the blue wire on the 3 pin harness can be used as a positive lock output and green can be used as a positive unlock output.ASE Certified