2nd starter 2001 grand caravan

Home / the12volt's Install Bay / Car Security and Convenience / 2nd starter 2001 grand caravan (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

kevin2

Member - Posts: 2

Joined: January 09, 2006

Posted: January 12, 2006 at 3:53 PM / IP Logged

Compustar 2WSS-S remote starter

2001 Grandcaravan

Before I start this install, I wanted to confirm the connections for the 2nd starter relay:

87 connects through a 180ohm resistor to the PURPLE / brown in the ignition harness.

86 connects to the controller connector 1 pin 5 (+ 2nd starter)

85 and 30 are connected to GND.

Can anyone confirm if this is correct?

Thanks.

dea,can

Copper - Posts: 284

Joined: January 12, 2006

Location: Saskatchewan, Canada

Posted: January 12, 2006 at 4:25 PM / IP Logged

87 to PURPLE / brown 150ohm resistor

85 ground out when running with 6amp diode gray band facing unit

86 to yellow wire

30 to ground

on the dodge caravan 2001 1/2 and up ,there is a extra wire present at the ignition swotch. this wire provides a diffrent voltage depending on the position of the in the ignition baril if you install a remote car starter you will also have to change the voltage on the wire or the car will crank and will not start.

dragon

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: January 12, 2006 at 4:30 PM / IP Logged

One end of Resistor goes to GROUND

Other end of Resistor goes to PIN 87

PIN 30 goes to Ignition Violet / Brown

PIN 86 to 12 Volts ( + ) Constant

PIN 85 to Negative while Starting / Running from R/S

VIOLET/BROWN and VIOLET/ORANGE Must See 180 OHM Resistor Between Them During Start Due To Multiplexing.

Don't Learn from Others Mistakes

You Might Be the One That Knows.

OhioMike1101

Silver - Posts: 343

Joined: August 22, 2004

Location: United States

Posted: January 12, 2006 at 7:22 PM / IP Logged

that Compustar unit comes with both a (+) and (-) starter output.

South Side Audio

2501 S. High St

Columbus, OH 43207

mike swanson

Copper - Posts: 290

Joined: January 28, 2003

Location: United States

Posted: January 12, 2006 at 7:59 PM / IP Logged

Wire Magic says use a resistor 180 to 200 so i used a 190 and it works fine. Use a relay to keep a good ground ( 0 Resistance out to start with then add the resitor after that Yu have prolly has some resistance comming out of the - start from the unit.

kevin2

Member - Posts: 2

Joined: January 09, 2006

Posted: January 12, 2006 at 8:54 PM / IP Logged

Thanks for the information. As ohiomike1101 stated the compustar unit does have a (+) 2nd starter output. I'll use that output to switch the relay which will connect the 180 ohm resistor to GND.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2nd starter 2001 grand caravan

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.