02 corvette trunk release

Home / the12volt's Install Bay / Car Security and Convenience / 02 corvette trunk release (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

carrman

Member - Posts: 16

Joined: December 10, 2003

Location: United States

Posted: March 17, 2006 at 7:33 PM / IP Logged

Im trying to find the right wire for trunk release at BCM. I have light blue, but there are several wires. More than one shows negative when I hit release. Is there a certain amount of negative it should show? any help like row# or pin would be helpful. thanks

Back to Top

Raymond4646

Copper - Posts: 121

Joined: July 10, 2005

Posted: March 17, 2006 at 7:52 PM / IP Logged

12volts	red	+	ignition harness
Starter	yellow	+	ignition harness
Second Starter
Ignition	pink	+	ignition harness
Second Ignition
Third Ignition
Accessory	orange	+	ignition harness
Second Accessory	brown	+	ignition harness
Keysense
Power Lock	RED / black	-	driver door module in door
Power Unlock	ORANGE / black	-	driver door module in door
Lock Motor
Unlock Motor
Parking Lights+	brown	+	headlight switch
Parking Lights-
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	gray/black (D), BLACK/ white(P)	-	BCM
Dome Supervision
Trunk/Hatch Pin	RED / black	-	BCM
Hood Pin	pink/black	-	BCM
Trunk/Hatch Release	lt. blue	-	BCM
Power Sliding Door
Factory Alarm Arm	arms with lock
Factory Alarm Disarm	lt. green	-	driver door module in door
Disarm No Unlock
Tachometer	white	ac	cluster or PCM, red plug, pin 10
Wait to start	N/A
Brake Wire	white	+	brake pedal switch
Parking Brake
Horn Trigger	black	-	BCM
Memory Seat 1
Memory Seat 2
Memory Seat 3

Back to Top

Raymond4646

Copper - Posts: 121

Joined: July 10, 2005

Posted: March 17, 2006 at 7:59 PM / IP Logged

If no one chimes in with the correct pin then, you must go thru and cut one wire at a time to find it. Just guess right the first time. LOL

Back to Top

NowYaKnow

Gold - Posts: 1,217

Joined: December 18, 2002

Posted: March 17, 2006 at 11:41 PM / IP Logged

B7-B8 Not Used

B9 LT BLU Trunk Release Relay Output - Coil

B10 BLK Horn Relay Output - Coil

As far as I can see the BCM should have 3 plugs. A 24 pin, 32 pin, and 16 pin. The wire you want is in the 24 pin. It should be the ONLY light blue wire in that 24 pin connector. The 32 pin connector should have 2 light blue wires, that you don't want. The 16 pin shouldn't have any light blue wires. Of course test to be sure, but it looks like the pin above is the one you want. I listed some of the other pins near it so it's easier to pick out. If any of this doesn't seem to go with what you are dealing with post back and I will check again. Hope it helps,

Mike

Back to Top

carrman

Member - Posts: 16

Joined: December 10, 2003

Location: United States

Posted: March 18, 2006 at 8:41 AM / IP Logged

Thanks for the replies, on my next day off I'll try it again.

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

02 corvette trunk release

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.