04 Silverado Sport side

Home / the12volt's Install Bay / Car Security and Convenience / 04 Silverado Sport side (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 11, 2006 at 7:41 PM / IP Logged

I am installing a Viper 560XV with a 457G GM Data bus interface first I know there are a lot of wires that are not used but I would like to use the neutral safety switch where can I hook it up? All so is it possible to get each the driver’s door to unlock then the passenger door with a second push of the remote? The 560XV says on the door lock harness green (-) lock (+) unlock, blue (+) lock (-) unlock do I hook them to the 457G green to light green and blue to blue and what gets hook to the blue/white wire on the 457G? Thanks for any help I'm use to older cars before databus :)

Twelvoltz

Platinum - Posts: 2,384

This member has made a donation to the12volt.com. Click here for more info.

This member consistently provides reliable information

Joined: March 24, 2005

Location: New Jersey, United States

Posted: November 11, 2006 at 8:33 PM / IP Logged

The neutral safety wire is not required on the 04 Silverado, as your truck will not start in gear. Just ground the h/3 BLACK/ white.

Yes, you can get driver's door priority unlocking with the 560xv.

Unlock Motor tan 5wi driver door module in door

You would use the main unlock negative output to 5wire this wire, use the light blue h2/1 for the unlock output and the main lock wire negative to the 457G, ignoring the + output status of these wires.

There are a couple of wires on the 560xv that are labeled as 'status output'. Any of these can be hooked to the blue/white on the 457.

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 11, 2006 at 8:53 PM / IP Logged

Thanks! just what I was looking for....

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 12, 2006 at 4:34 PM / IP Logged

I am installing a Viper 560XV with a 457G GM Data bus interface The lites flash during remote start my guess is I'm going to have to power the 2 aux wire(brown) to get them to say on. here is a problem the doors will not lock when I hit the lock/arm button the doors unlock same with the unlock/disarm and the door trigger works when the door is closed not open? might just be the shock sensor but weard never the less. Blue 457 to blue door lock harness on the 560, light green 457 to green door lock harness on the 560, Green 457 to H1/5 green on the 560 Help and yes I tried to flip the green wires around Everything else works remote start, shock sensor, hood pin, help.

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: November 12, 2006 at 4:53 PM / IP Logged

What did you connect the grey/black of the 457G to?

You need to program parking light flash to constant on the Viper 560. The default setting is flashing. Not powering the brown acc 2 has nothing to do with it.

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 12, 2006 at 5:06 PM / IP Logged

The park lites are fine its getting dark here so the head lights are trying to come on. Nothing on gray/black

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: November 12, 2006 at 5:18 PM / IP Logged

Go into programming and change the parking lights output to constant. Your headlights will stop flashing.

The grey/black needs to go to the grey/black wire that leads to the domelight in the truck. You can find it in the drivers A-Pillar. If there is an underdash light, you can also get it there.

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 12, 2006 at 5:26 PM / IP Logged

Ok I will try that Thanks

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 12, 2006 at 6:19 PM / IP Logged

Ok I hooked up the the gray/black no change the unit will not go into program mode nor will it learn the tach

magicmanwv

Member - Posts: 13

Joined: October 09, 2006

Posted: November 12, 2006 at 7:01 PM / IP Logged

Ok I have ck'ed everything this truck has had a viper in it before I think it has been a stolen recovery the door chimes have never worked and the speakers have a short in them I pulled the radio to ck it and it has $600 wrote on it and a check mark do you think that the radio might be the problem? also the doors try to unlock when you turn on the headlights. Help

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.