the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

prostart, 93 ford escort


Post ReplyPost New Topic
< Prev Topic Next Topic >
dlambe 
Copper - Posts: 57
Copper spacespace
Joined: December 06, 2005
Location: Saskatchewan, Canada
Posted: November 24, 2006 at 9:24 PM / IP Logged  
K guys I want to see who can help me out with this one, before I get started some background info;
1) car; 93 lx, 5 spd, basic deal (no cruise, a/c, alarm, wtc. just the basic car)
2)I am a heavy equipment tech and a wiring guru at work.
Now I bought a ct3260 remote starter from crappy tire and installed it, I have checked all the wiring 3 times for faults and or mistakes, I found none. The problem comes when I attempt to program this POS. I flash the hood pin as per normal and that works fine, however it will not accept the transmitter code, the park lights do come on but stay on solid they do not flash 5 times as per the instructions. I need help here guys its -20 celsius and I want to get this damn thing workin right. I tried both methods of programming it and neither worked, I have even reset the damn thing to no avail. The site for it is at www.prostart.org I am stumped any help would be appreciated. It does all the other functions bang on as well (ie, reset, valet mode, etc...)
dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 1:38 AM / IP Logged  
i have done a few of them  they are the same as the  autostrat line same brand  u sure u are not bring up the events playback mode have u tryed the assistance button on the module  its a little tricky if have not done  a few then its a snap you say you flash the hood pin and that works fine how long do you hold down the lock button  i had some take longer then usual also may have a faulty module
dragon
dlambe 
Copper - Posts: 57
Copper spacespace
Joined: December 06, 2005
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 10:00 AM / IP Logged  

I flash the hood pin by pressing it down for 4 seconds then letting go and quiclky pushing it down and releasing, then I turn the key on and off then I hold the lock button down for like 15 seconds at least. After about 3 seconds the park licghts come on and stay on for about 20 seconds. I have used the pab do do this as well to see if that worked.

dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 12:40 PM / IP Logged  
sure u have the right ignition wire hooked up  try programmming tach 
dragon
dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 12:49 PM / IP Logged  
when u release the pin the second time you have snap the pin fast  so when you press it down the first time then the second time dont press and hold  like i said you need to snap it fast  press hold let go and snap second time.
dragon
dlambe 
Copper - Posts: 57
Copper spacespace
Joined: December 06, 2005
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 4:32 PM / IP Logged  
ok I went back to canadian tire and got a new one to replace the one I had, worked nicely, I programmed the remote and it recieves the signal no problem. Now this is where it gets confusing, can someone run down the process with me from the step after programming the remote, since when I did the tach programming I noticed that the park brake had to be disengaged for it to work for tach programming. I got to the step that takes you to idle mode but after I press button 2 when I am out of the vehicle and it shuts down the vehicle does not start again when I press button 2.
dlambe 
Copper - Posts: 57
Copper spacespace
Joined: December 06, 2005
Location: Saskatchewan, Canada
Posted: November 25, 2006 at 4:33 PM / IP Logged  

also is it necessary for me to go into programming mode with this model?

dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: November 26, 2006 at 1:16 AM / IP Logged  

park lights flash,

dragon
dlambe 
Copper - Posts: 57
Copper spacespace
Joined: December 06, 2005
Location: Saskatchewan, Canada
Posted: November 26, 2006 at 10:24 AM / IP Logged  
no after the vehicle shuts down when I press button 2 for idle mode there is nothing no park lights flash, however when I press 1 the lights do flash, 3 times when press it once and 2 times if I press it a 2nd time.
dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: November 26, 2006 at 2:17 PM / IP Logged  
so u can get it in ready mode ,all doors closed ebrake on press start button car stays running get out of car shut down car by remote  push start button car start  then if dont start do the events play back count the flashes look in book to see whats happen.
dragon
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 9, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer