the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

ultrastart 1270tl

Home / the12volt's Install Bay / Car Security and Convenience / ultrastart 1270tl (Topic Closed Topic Closed)
Welcome Guest :)

Post ReplyPost New Topic
< Prev Topic Next Topic >
ziggyb222 
Silver - Posts: 593
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: January 04, 2004
Location: Maine, United States
Posted: October 15, 2007 at 7:50 PM / IP Logged  
Started to install my first Ultrastart the other day. I have been doing crimestopper for the past couple of years. I got everything hooked up and soldered. Went into the tach set up and all went well. The unit confirmed the tach setting. Hit the start button and nothing happens. I tried to reprogram the transmitters and they would not confime they where done. Locks and everything do not function at all.. Any little trick I might be missing on programming the transmitters????
KarTuneMan 
Platinum - Posts: 7,056
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member consistently provides reliable informationspace
Joined: December 14, 2004
Location: Isle Of Man
Posted: October 15, 2007 at 8:15 PM / IP Logged  

More info please.....my e.s.p. skills are slipping.

Year make and model of your car

ziggyb222 
Silver - Posts: 593
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: January 04, 2004
Location: Maine, United States
Posted: October 16, 2007 at 3:16 AM / IP Logged  
It is an 05 Ford Five hundred. Had a Crimestopper piece of crap starter in it. Replaced it with this Ultra... Unit just seems non responsive like the transmitters are not programed.....
xtremej 
Gold - Posts: 1,440
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 24, 2006
Location: United States
Posted: October 16, 2007 at 12:28 PM / IP Logged  
When you try to start it are the pking lights flashing, how many blinks do you get? If not make sure you don't have it in service mode, indicated by the leds on solid (antenna)
ziggyb222 
Silver - Posts: 593
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: January 04, 2004
Location: Maine, United States
Posted: October 16, 2007 at 1:14 PM / IP Logged  
I have taken it n and out of service mode.. no leds on now.. and there doesnt seem to be any diagnostic codes in the memory because I get no flashes on the leds. I had left the fuse out of the parklights because I wanted to make sure i programmed the right polarity, i cannot imagine that being an issue, I hear the relay activate when I am changing program modes... These units are just new to me as far as programming goes... I need to get more time to work with these.. Thanks for your help by the way.....
xtremej 
Gold - Posts: 1,440
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 24, 2006
Location: United States
Posted: October 16, 2007 at 1:18 PM / IP Logged  
the RED / white doubles as either trunk release or negative trigger parking lights. white wire with fuse is only postive trigger.
xtremej 
Gold - Posts: 1,440
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 24, 2006
Location: United States
Posted: October 16, 2007 at 1:18 PM / IP Logged  
It is remote starting now?
ziggyb222 
Silver - Posts: 593
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: January 04, 2004
Location: Maine, United States
Posted: October 16, 2007 at 1:23 PM / IP Logged  
I will get the vehicle back soon... Will double check the parklights....
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: October 16, 2007 at 7:23 PM / IP Logged  
Sounds to me like the remotes need to be programmed.
And about your comment about leaving the fuse out of the parking light wire....
The white wire will always be a (+) output, and the RED / white wire will always be a (-) output. The programming option your are referring to is the function that each wire controls. By default white is parking light, and RED / white is trunk release. After you change the programming the white is trunk release, and RED / white is parking lights.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 16, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer