programming astro start 803 remote

Home / the12volt's Install Bay / Car Security and Convenience / programming astro start 803 remote (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

zorrodog

Member - Posts: 4

Joined: December 12, 2005

Posted: November 18, 2007 at 7:38 PM / IP Logged

Hi Folks.........we lost our remote for an Astro Start model 803 remote starter. Have an extra remote but it needs to be programmed, can anyone help us out and give directions on how it is done?? Thanks

Back to Top

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: November 18, 2007 at 8:58 PM / IP Logged

open the hood
place key in the ignition & turn to the run "ON"
apply the brake once
within 10 sec turn the key from run to stop 3 times
if successful, parking lights will flash 4 times
press any button on the remote, when new code is learned, it will confirm with 1 flashing parkinglight
repeat the above procedure for each remote that has to be programmed (up to 4)
apply the brake
remote is now added to the system
close the hood

Back to Top

saskpuller

Copper - Posts: 144

Joined: November 14, 2006

Location: Canada

Posted: November 19, 2007 at 10:25 PM / IP Logged

or if you can get access to the module

- Dip switch 8 up, push the start button on the remote, the unit should make some clicking noise.

- dip switch down and press brake. DOne

Back to Top

zorrodog

Member - Posts: 4

Joined: December 12, 2005

Posted: November 19, 2007 at 11:35 PM / IP Logged

I tried the procedure that moonliter posted and could not get that to work.Will try the dipswitch procedure.....Thanks

Back to Top

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: November 20, 2007 at 11:54 AM / IP Logged

If you haven't got the remote programmed, try this again

open the hood ( make sure hood pin switch is properly grounded )

place key in the ignition & turn to the run "ON"

apply the brake once

within 10 sec turn the key from run "ON" to stop "OFF" 3 times ( off, on, off, on, off )

if successful, parking lights will flash 4 times ( if you don't get the parking light flashes, that means the above steps are not done correctly )

press any button for a second (led comes on, goes out and then back on blink ......until it stops flashing ) on the remote, when new code is learned,

it will confirm with 1 flashing parkinglight

repeat the above procedure for each remote that has to be programmed (up to 4)

apply the brake

remote is now added to the system

close the hood

Back to Top

KarTuneMan

Platinum - Posts: 7,056

This member has made a donation to the12volt.com. Click here for more info.

This member consistently provides reliable information

Joined: December 14, 2004

Location: Isle Of Man

Posted: November 20, 2007 at 4:24 PM / IP Logged

saskpuller wrote:

or if you can get access to the module

- Dip switch 8 up, push the start button on the remote, the unit should make some clicking noise.

- dip switch down and press brake. DOne

This should do the trick!

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

programming astro start 803 remote

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.